Re: gecko burned again ?oil dripping on the motor..

In the process of inspecting the problem on the y axis I noticed
that the y axis motor sits directly under the ball screw with oil
dripping down onto the wires and the motor. Is it possible that the
oil could get inside the motor or down the wires onto the
connections and cause a short? If there is oil internally is the
motor possibly damaged?

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Keith Clark" <mail@t...>
wrote:

>
> I now have 3 separate 10 amp slow blow fuses, one leading to the
> power input on each drive. The motors are rated at 7 amps. Is

that

> the correct fuse to be using?
>
> Thanks,
> Keith
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "john labutski"

<kd6wd@c...>

> wrote:
> > Jon
> > You have an excellent point. Keith could probably test this with

a

> new
> > Gecko. He should just add the correct amp fuses to the motor
> drive lines.
> > When one fuse pops he will probably find you are correct.
> >
> > Your comments also bring up another great point to consider .
> Fuses and
> > fuse holders are cheap compared to driver boards as well as
> computers. I've
> > been a ham radio operator for a long time and over the years

fuses

> have
> > saved me thousands of dollars worth of equipment when a power
> supply or a
> > transformer went south on me. Old "Buss" and me are great

buddies.

> >
> > John
> > ----- Original Message -----
> > From: "Jon Elson" <elson@p...>
> > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > Sent: Sunday, November 07, 2004 1:26 PM
> > Subject: Re: [CAD_CAM_EDM_DRO] gecko burned again
> >
> >
> > >
> > > Keith Clark wrote:
> > >
> > > >Well, the y axis gecko drive burned again this morning. This
> time
> > > >there are no loose wires. I was doing very little with the
> machine
> > > >and had just turned it on when during a y axis G0 move, the
> drive
> > > >burned up. I assume this is an indication that the Gecko

cannot

> > > >handle the motor I am using. This is an old topic and I have
> asked
> > > >for help with this problem before. The mill is a Bridgeport
> Series
> > > >1 CNC originally controlled by Boss 6 but now using Anaheim
> Nema 42
> > > >high torque stepper motors and Mach2 software with a Campbell
> > > >breakout board.
> > > >
> > > >At this point is seems reasonable to try another brand drive?
> > > >
> > > >
> > > I think you need to retire that MOTOR. There is nothing wrong
> with
> > > the Gecko drive, when used with good motors. But, one of its
> weaknesses
> > > is that shorts to ground, or just plain internal shorts in the
> motor
> > > windings
> > > will pop transistors in the Gecko drive. I think you'll find
> the Rutex,
> > > Xylotex,
> > > etc. drives all have this same weakness. After blowing TWO
> Geckos on
> > > the SAME motor, doesn't that tell you something? Why didn't

the

> X or Z
> > > drivers blow? Why always the Y axis?
> > >
> > > Explanation: Your Y motor has an intermittent short. How

much

> you are
> > > doing with it doesn't make much difference. I assume the

motors

> heat
> > > up, even when idling. The heat probably causes the short to
> develop
> > > every once in a while, when the winding expands from the heat.
> > >
> > > Jon
> > >
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a...,
> > timg@k...
> > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > [Moderators]
> > > URL to this group:

http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider

this

> to be a
> > sister site to the CCED group, as many of the same members are
> there, for OT
> > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >