CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Reversing switch-

on 2004-12-16 06:29:49 UTC
The three way is a double pole single throw, not a single pole double
throw. I see now that I got it correct at the top but that I made a
mistake at the bottom of the page <redfaced> Yes you would need a
separate start stop, unless you picked up a three position "left off
right" switch. The "four way" would simply add a reverse.
Mike Wood, Cincinnati

Stephen Wille Padnos wrote:

>Roy J. Tellason wrote:
>
>
>
>>On Wednesday 15 December 2004 06:21 pm, Michael Wood, Cincinnati wrote:
>>
>>
>>
>>
>>>You want either a single throw double pole switch or a double throw
>>>double pole double throw toggle switch (you just don't use one of the
>>>poles)--
>>>
>>>
>>>
>>>
>>This is incorrect. You cannot exchange _two_ wires with a single pole switch.
>>
>>
>>
>>
>>>between $5 and $10. I think Loews has them in the electrical
>>>section with the Gardner-Bender stuff. You could use a "3 way" light
>>>switch, which does the same thing. Basically one position allows for a
>>>straight through feed, while the other position crosses them.
>>>
>>>
>>>
>>>
>>A "3-way" switch is just a single-pole, double-throw switch.
>>[snip]
>>
>>
>>
>In fact, to expand on this - you can't even use a "4-way" switch. Those
>swap two wires, but both wires are always connected. You could use one
>of these to change direction only if you have a separate start/stop control.
>
>- Steve
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
>

Discussion Thread

Are you kidding??? 2004-12-15 13:12:51 UTC Reversing switch- Roy J. Tellason 2004-12-15 13:27:07 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- JanRwl@A... 2004-12-15 13:31:32 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Alan Marconett 2004-12-15 14:15:25 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- John J. Clark 2004-12-15 14:22:53 UTC RE: [CAD_CAM_EDM_DRO] Reversing switch- John J. Clark 2004-12-15 14:31:11 UTC RE: [CAD_CAM_EDM_DRO] Reversing switch- Michael Wood, Cincinnati 2004-12-15 18:07:45 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Roy J. Tellason 2004-12-15 20:36:32 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Stephen Wille Padnos 2004-12-15 20:59:15 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Raymond Heckert 2004-12-15 21:26:18 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Wayne 2004-12-16 03:38:10 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Wayne 2004-12-16 03:41:27 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Michael Wood, Cincinnati 2004-12-16 06:17:47 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Andy Wander 2004-12-16 06:25:02 UTC RE: [CAD_CAM_EDM_DRO] Reversing switch- Michael Wood, Cincinnati 2004-12-16 06:29:49 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Andy Wander 2004-12-16 06:45:22 UTC RE: [CAD_CAM_EDM_DRO] Reversing switch- Michael Wood, Cincinnati 2004-12-16 07:37:16 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Michael Wood, Cincinnati 2004-12-16 07:38:45 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Stephen Wille Padnos 2004-12-16 07:49:02 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- Dave Fisher 2004-12-16 14:34:41 UTC RE: [CAD_CAM_EDM_DRO] Reversing switch- JanRwl@A... 2004-12-16 16:42:15 UTC Re: [CAD_CAM_EDM_DRO] Reversing switch- turbulatordude 2004-12-16 17:47:11 UTC Re: Reversing switch-