CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to Gecko 320

Posted by John Guenther
on 2005-01-01 11:53:39 UTC
Ok, let's assume that we are using a .2 inch per rev lead screw on this mill
with 500 cpr encoders. That would be 500*4 = 2000 pulses per rev. 2000*5 =
10000 pulses per inch * 120 = 1200000 pulses per minute. 120000 / 60 =
20000 pulses per second for 120 inches per minute. Mach2 can run at 45000
pulses per second so you could easily get 120IPM on both the X and Y axis
during a rapid move.

John Guenther

-----Original Message-----
From: Fred Smith [mailto:imserv@...]
Sent: Saturday, January 01, 2005 14:36
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to
Gecko 320




--- In CAD_CAM_EDM_DRO@yahoogroups.com, "shadi_salhab_78"
<salhab@m...> wrote:
>

> I wana ask you what is the reduction ratio of the timming belt you
> are using to get 120 IPM . The G320 does not have a step
multiplaier
> and no program can give you more than 45000 ppm , so I think the
120
> IPM is imposible with G320 specially on a bridgport ?!


DeskCNC will run at 125,000 steps per second in Windows and several
of the DOS based controllers will also run up to 75,000 or 100,000
steps per second.

Fred Smith - IMService
http://www.cadcamcadcam.com/hobby





Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links

Discussion Thread

Joel 2004-12-29 08:12:11 UTC Wanted: Servo Motors that interface to Gecko 320 turbulatordude 2004-12-29 18:54:55 UTC Re: Wanted: Servo Motors that interface to Gecko 320 R Rogers 2004-12-30 06:47:08 UTC Re: [CAD_CAM_EDM_DRO] Wanted: Servo Motors that interface to Gecko 320 John Meissner 2004-12-30 09:12:12 UTC Re: Wanted: Servo Motors that interface to Gecko 320-Ron R Rogers 2004-12-30 15:42:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to Gecko 320-Ron Jon Elson 2004-12-30 18:44:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to Gecko 320-Ron shadi_salhab_78 2005-01-01 09:57:55 UTC Re: Wanted: Servo Motors that interface to Gecko 320 vrsculptor 2005-01-01 11:09:16 UTC Re: Wanted: Servo Motors that interface to Gecko 320 Fred Smith 2005-01-01 11:36:40 UTC Re: Wanted: Servo Motors that interface to Gecko 320 John Guenther 2005-01-01 11:53:39 UTC RE: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to Gecko 320 R Rogers 2005-01-01 12:20:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to Gecko 320 Roy J. Tellason 2005-01-01 14:33:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Wanted: Servo Motors that interface to Gecko 320