CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay

Posted by Andy Wander
on 2005-01-28 15:19:17 UTC
Yeah, that'll work. I had these nice little PC mount relays that can switch
up to 1A and only take about 10mA at 5V to turn them on, so I used them.

Andy Wander
Verrex Corporation

-----Original Message-----
From: turbulatordude [mailto:dave_mucha@...]
Sent: Friday, January 28, 2005 5:32 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay



--- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@v...>
wrote:
> Alan:
>
> I'm talking about the huge inductive "spike" that occurs when
the "control",
> whether it is a switch, a parallel port pin, or whatever, opens the
circuit.
> This causes a voltage spike that WILL fry transistors!
>
> But the OP has indicated that he DID have a suppression diode
installed
> across the coil, so that is probably not the problem.
>
>
> And it is very possible to control relays with the parallel port
directly;
> I'm controlling some small 5V relays directly with my parallel
port. You
> just nned to make sure that the relays source less current than the
port can
> sink(low-active is recommended).
>
>
>
> Andy Wander
> Verrex Corporation

Most of us who have made such a circuit drive a opto-isolator from
the parallal port, then a transistor from the opto and the transistor
can be a small 2n2222 or even a TIP120 or such.

But, the simplest way is to just use a SSR and save all the problems.

Just make sure the SSR is rated for the thing being driven. Most are
AC only or DC only. so, you cannot use a DC only to drive an AC
motor.

Dave





Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links

Discussion Thread

bertmantx 2005-01-27 19:07:15 UTC Getting Parallel port to run relay Robert Campbell 2005-01-27 19:25:28 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay codeSuidae 2005-01-27 20:02:30 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay lanebarr@b... 2005-01-27 20:07:49 UTC re:Getting Parallel port to run relay bertmantx 2005-01-27 20:28:50 UTC Re: Getting Parallel port to run relay Stephen Wille Padnos 2005-01-27 20:35:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay bertmantx 2005-01-27 20:55:31 UTC Re: re:Getting Parallel port to run relay bertmantx 2005-01-27 20:59:10 UTC Re: Getting Parallel port to run relay codeSuidae 2005-01-27 21:14:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay codeSuidae 2005-01-27 21:40:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay JanRwl@A... 2005-01-27 23:39:39 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay JanRwl@A... 2005-01-27 23:43:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay jerrydotson32531 2005-01-28 03:25:21 UTC Re: Getting Parallel port to run relay Wayne 2005-01-28 03:34:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay Andy Wander 2005-01-28 05:20:20 UTC RE: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay vrsculptor 2005-01-28 06:21:46 UTC Re: Getting Parallel port to run relay JCullins 2005-01-28 06:47:32 UTC Re: [CAD_CAM_EDM_DRO] re:Getting Parallel port to run relay JCullins 2005-01-28 06:54:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay turbulatordude 2005-01-28 07:37:29 UTC Re: Getting Parallel port to run relay accessing the paralle port bertmantx 2005-01-28 10:07:02 UTC Re: Getting Parallel port to run relay bertmantx 2005-01-28 10:09:31 UTC Re: Getting Parallel port to run relay bertmantx 2005-01-28 10:17:51 UTC Re: Getting Parallel port to run relay Codesuidae 2005-01-28 10:34:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay Alan Marconett 2005-01-28 11:24:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay Alan Marconett 2005-01-28 12:02:31 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Andy Wander 2005-01-28 12:28:37 UTC RE: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Roy J. Tellason 2005-01-28 12:37:22 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Alan Marconett 2005-01-28 13:13:07 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay turbulatordude 2005-01-28 14:32:43 UTC Re: Getting Parallel port to run relay Andy Wander 2005-01-28 15:19:17 UTC RE: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay Scott L Golden 2005-01-28 17:47:35 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Wayne 2005-01-28 18:25:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay Andy Wander 2005-01-28 18:50:57 UTC RE: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Scott L Golden 2005-01-28 19:18:19 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay turbulatordude 2005-01-28 19:54:06 UTC Re: Getting Parallel port to run relay Alan Marconett 2005-01-29 10:37:20 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Tom Hubin 2005-01-29 12:40:35 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Tom Hubin 2005-01-29 13:17:49 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay codeSuidae 2005-01-29 13:19:27 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Scott L Golden 2005-01-29 17:00:14 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Raymond Heckert 2005-01-29 18:51:29 UTC Re: [CAD_CAM_EDM_DRO] Getting Parallel port to run relay Tom Hubin 2005-01-30 16:07:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay Roy J. Tellason 2005-01-30 16:53:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Getting Parallel port to run relay