Re: Jeff's mill drill
Posted by
len_tikular
on 2005-02-09 11:38:10 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@y...> wrote:
It's all a bit of a jungle. Jeff's looked like what I need so I'll
give it a go. One thing that did startle me was the way he achieved
the third axis control. I thought that was good.
George
<dave_mucha@y...> wrote:
>Thanks Dave, I'll go see.
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "len_tikular" <george@p...>
> wrote:
> >
> > I'd like to get in touch with Jeff. He has some pictures of his
> > Mill/drill conversion in the 'Photos' section.
> >
> > Jeff maybe you could help me convert my Eagle25.
> >
> > Thanks
> >
> > George
>
>
> Hi Gerorge, Dave here.
>
>
> If Jeff doesn't reply, just review the list, get PGOFFLINE and pull
> down the whole list so you can review it for each of yoru questions.
>
>
> Check out a few other sites.
>
> http://www.homecnc.info/ballscrew.htm
>
> for screws replacement.
>
> and
>
> http://truetex.com/ymount.htm
>
> for mounting motors
>
> Much of this is straight forward cut and paste stuff.
>
> Pick your strong suit, mechanical stuff, electronics, whatever and
> start with that.
>
> My one word of caution is to make sure that when one thing goes in,
> it does not interfere with another.
>
>
> There are other lists as well.
>
> http://groups.yahoo.com/group/mill_drill/
>
> If you are one of those guyse who likes to read every bit possible,
> you may find that a 3-ring binder and print out all this stuff.
> Seperate into sections.
>
> If the last couple years of on-line searching, I think I can safely
> say I have forgotten more web sites than most people can remember.
>
> Dave
It's all a bit of a jungle. Jeff's looked like what I need so I'll
give it a go. One thing that did startle me was the way he achieved
the third axis control. I thought that was good.
George
Discussion Thread
len_tikular
2005-02-09 05:49:33 UTC
Jeff's mill drill
turbulatordude
2005-02-09 08:15:56 UTC
Re: Jeff's mill drill
len_tikular
2005-02-09 11:38:10 UTC
Re: Jeff's mill drill
AbbyKatt
2005-02-09 12:10:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill
turbulatordude
2005-02-09 12:55:01 UTC
Re: Jeff's mill drill Timing pulley milling cutter
Alan Marconett
2005-02-09 13:45:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill Timing pulley milling cutter
cnc_4_me
2005-02-09 13:53:25 UTC
Re: Jeff's mill drill Timing pulley milling cutter
turbulatordude
2005-02-09 18:05:23 UTC
Re: Jeff's mill drill Timing pulley milling cutter
cnc_4_me
2005-02-09 22:44:03 UTC
Re: Jeff's mill drill Timing pulley milling cutter
Bruce Pigeon
2005-02-10 05:02:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill Timing pulley milling cutter
turbulatordude
2005-02-10 07:36:38 UTC
re: Timing pulley milling cutter
erie
2005-02-10 12:16:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill Timing pulley milling cutter
turbulatordude
2005-02-10 19:46:21 UTC
Re: Timing pulley selection software
cnc_4_me
2005-02-10 20:52:56 UTC
Re: Timing pulley selection software