Re: Timing pulley selection software
Posted by
turbulatordude
on 2005-02-10 19:46:21 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "cnc_4_me" <cnc4me@g...>
wrote:
Here you can request a copy of the program that will help in
selection of the belts.
In my case, I'm starting out with a high speed, 5,400 RPM treadmill
motor, and reducing it down to a plasma table that can theoretically
do 500 ipm.
http://www.gates.com/dfcampaign/index.cfm?go=btgtsdf1103
Dave
wrote:
>any
> Well i would order belts from local bearing house, do not know of
> discount house.a
>
> I would really only want to use PowerGrip GT2. I looked around for
> few hours earlier for specs and could only find a sketch of varioussee
> belt shapes for comparison with no dimensions.
>
> I think I found the patent here, but no dimensions.
>
> http://www.freepatentsonline.com/4403979.html?highlight=powergrip
>
> Any ideas were to find them
>
> Wally
>
>
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
> <dave_mucha@y...> wrote:
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "cnc_4_me" <cnc4me@g...>
> > wrote:
> > >
> > > >
> > > > I sent a request to a custome milling cutter grinder guy to
> > howconsider
> > > > much it would cost to get a milling cutter to make a belt
> > grouve.
> > > > then it would be a matter of just turning the OD and milling
> the
> > > > slots.
> > > >
> > >
> > >
> > >
> > > I am very interested in your findings, I was thinking of doing
> the
> > > same thing.
> > >
> > > The information I gathered on pulleys is the only two to
> > arehp
> > > HTD and power grip GT2. Of these types GT2 has almost 2x the
> > > rating for same size belt. And GT2 has much less backlash. Ifsplit
> you
> > > want HTD for some reason then you would make the trough in the
> > > pulley .004" higher than spec to reduce backlash (per gates).
> > >
> > > I have not gotten to the point of finding the exact specs and
> > > dimensions for the cutter for these pulleys and do not know if
> they
> > > are published .Also if this gets figured out maybe we could
> > theI spoke to a Gates tech and he offered a link to the Gates site.
> > > cost if more than 1 cutter cost less money
> > >
> > > Wally
> >
Here you can request a copy of the program that will help in
selection of the belts.
In my case, I'm starting out with a high speed, 5,400 RPM treadmill
motor, and reducing it down to a plasma table that can theoretically
do 500 ipm.
http://www.gates.com/dfcampaign/index.cfm?go=btgtsdf1103
Dave
Discussion Thread
len_tikular
2005-02-09 05:49:33 UTC
Jeff's mill drill
turbulatordude
2005-02-09 08:15:56 UTC
Re: Jeff's mill drill
len_tikular
2005-02-09 11:38:10 UTC
Re: Jeff's mill drill
AbbyKatt
2005-02-09 12:10:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill
turbulatordude
2005-02-09 12:55:01 UTC
Re: Jeff's mill drill Timing pulley milling cutter
Alan Marconett
2005-02-09 13:45:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill Timing pulley milling cutter
cnc_4_me
2005-02-09 13:53:25 UTC
Re: Jeff's mill drill Timing pulley milling cutter
turbulatordude
2005-02-09 18:05:23 UTC
Re: Jeff's mill drill Timing pulley milling cutter
cnc_4_me
2005-02-09 22:44:03 UTC
Re: Jeff's mill drill Timing pulley milling cutter
Bruce Pigeon
2005-02-10 05:02:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill Timing pulley milling cutter
turbulatordude
2005-02-10 07:36:38 UTC
re: Timing pulley milling cutter
erie
2005-02-10 12:16:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Jeff's mill drill Timing pulley milling cutter
turbulatordude
2005-02-10 19:46:21 UTC
Re: Timing pulley selection software
cnc_4_me
2005-02-10 20:52:56 UTC
Re: Timing pulley selection software