RE: [CAD_CAM_EDM_DRO] EMC ,STG-II
Posted by
Babar
on 2005-05-25 21:16:10 UTC
Hi All,
--- Keith Rumley <DSCadCam@...> wrote:
program ? or in MDI before closing the software or
system?
value #5220 each time before restarting the system?
Will it also solve the problem of not supporting
G54-G59?
Babar
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
--- Keith Rumley <DSCadCam@...> wrote:
> Babar,You mean I should give G92.2 at the end of each
>
> > Each time when the System is is restarted or the
> software is
> > closed and re-launched (without restarting the
> PC) the
> > Software forgets it's previous X, Y and Z
> coordinates
> > and loads strange values.Is there any way to
> ensure that
> > after closing the EMC or PC, EMC restore it's last
> values of
> > X, Y and Z ?
>
> EMC re-loads with G92 offsets in effect. Sounds like
> you're looking at that.
> Make sure they are off by a G92.2 (saves them for
> re-use), or G92.1 (Clears
> them out of the parameter file, too.)
program ? or in MDI before closing the software or
system?
> It is a good idea to make sure G92 is off beforeUsing MDI mode ?????
> setting coordinate system
> offsets, as well.
> You might also check to see what coordinate systemThese values are either 1 or 0 , should I cset this
> you were in before
> exiting EMC. EMC boots to the value of .var file
> variable #5220, 1-9
> (G54-G59.3). If for some odd reason this was changed
> to be different than
> the last coordinate system, you may be in a
> different coordinate system.
value #5220 each time before restarting the system?
Will it also solve the problem of not supporting
G54-G59?
>regards
> A long shot problem may be the linux user you are
> logged in as doesn't have
> file write permissions for emc.var. If not, the
> simple fix is to log in as
> root user, get to the command line, go to
> usr/local/emc/ directory, and type
> 'chmod 777 emc.var'.
>
> Regards,
>
> Keith Rumley
Babar
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
Discussion Thread
shadi_salhab_78
2005-05-18 23:11:36 UTC
Backlash effect on Part accuracy
Jon Elson
2005-05-19 08:04:12 UTC
Re: [CAD_CAM_EDM_DRO] Backlash effect on Part accuracy
shadi_salhab_78
2005-05-20 22:20:35 UTC
Re: Backlash effect on Part accuracy
Tom Hubin
2005-05-20 22:56:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash effect on Part accuracy
Jon Elson
2005-05-21 12:54:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash effect on Part accuracy
Michael Larson
2005-05-21 15:49:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash effect on Part accuracy
turbulatordude
2005-05-21 16:42:17 UTC
Re: Backlash effect on Part accuracy
Luke1027
2005-05-21 17:20:35 UTC
[CAD_CAM_EDM_DRO] Choosing Power/Volts on Stepper Motor
Robert Campbell
2005-05-21 17:27:27 UTC
Re: [CAD_CAM_EDM_DRO] Choosing Power/Volts on Stepper Motor
Luke1027
2005-05-21 18:13:12 UTC
Re: [CAD_CAM_EDM_DRO] Choosing Power/Volts on Stepper Motor
Robert Campbell
2005-05-21 18:51:33 UTC
Re: [CAD_CAM_EDM_DRO] Choosing Power/Volts on Stepper Motor
turbulatordude
2005-05-21 19:02:18 UTC
Re: Choosing Power/Volts on Stepper Motor
Jon Elson
2005-05-21 23:06:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash effect on Part accuracy
Jon Elson
2005-05-21 23:09:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash effect on Part accuracy
R Rogers
2005-05-22 06:09:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Backlash effect on Part accuracy
Michael Larson
2005-05-24 15:37:20 UTC
Controlling +/- 10V Servo Amps
Codesuidae
2005-05-24 18:07:35 UTC
Re: [CAD_CAM_EDM_DRO] Controlling +/- 10V Servo Amps
Jon Elson
2005-05-24 20:37:49 UTC
Re: [CAD_CAM_EDM_DRO] Controlling +/- 10V Servo Amps
Jon Elson
2005-05-24 20:40:16 UTC
Re: [CAD_CAM_EDM_DRO] Controlling +/- 10V Servo Amps
Michael Larson
2005-05-24 21:08:23 UTC
Re: [CAD_CAM_EDM_DRO] Controlling +/- 10V Servo Amps
David Speck
2005-05-24 21:16:07 UTC
Re: [CAD_CAM_EDM_DRO] Controlling +/- 10V Servo Amps
Babar
2005-05-24 21:57:04 UTC
Re: [CAD_CAM_EDM_DRO] EMC ,STG-II
Alan Marconett
2005-05-25 08:07:06 UTC
RE: [CAD_CAM_EDM_DRO] EMC ,STG-II
Jon Elson
2005-05-25 10:13:01 UTC
Re: [CAD_CAM_EDM_DRO] EMC ,STG-II
Keith Rumley
2005-05-25 14:36:31 UTC
RE: [CAD_CAM_EDM_DRO] EMC ,STG-II
Babar
2005-05-25 21:16:10 UTC
RE: [CAD_CAM_EDM_DRO] EMC ,STG-II
Paul
2005-05-26 07:53:30 UTC
Re: [CAD_CAM_EDM_DRO] EMC ,STG-II
Babar
2005-05-26 20:40:45 UTC
Re: [CAD_CAM_EDM_DRO] EMC ,STG-II
Keith Rumley
2005-05-27 04:20:44 UTC
RE: [CAD_CAM_EDM_DRO] EMC ,STG-II