Re: [CAD_CAM_EDM_DRO] BDI-4.20 Software Installation
Posted by
David A. Frantz
on 2005-08-03 20:30:37 UTC
Hi guys;
just a bit of info here, I have an old computer I tried to load BDI-4.46
I believe that also had issues. Never pursuded it as the whole CNC is
on the back burner while pursuing a bunch of other issues. The board
is an old ASUS with and on board SCSI controller. Linux loads
aic-7xxx no matter what I tried to do.
I would have mentioned it earlier but I simply don't have time to pursue
this debug wise. I haven't loaded 4.20 yet either so I don't know if
that helps. Apparently it doesn as the description below is pretty
close to what I was seeing. I think it is a realtime/linux issue the
machine ran the distro find until an attempt to run EMc is made.
Thanks
Dave
Jon Elson wrote:
just a bit of info here, I have an old computer I tried to load BDI-4.46
I believe that also had issues. Never pursuded it as the whole CNC is
on the back burner while pursuing a bunch of other issues. The board
is an old ASUS with and on board SCSI controller. Linux loads
aic-7xxx no matter what I tried to do.
I would have mentioned it earlier but I simply don't have time to pursue
this debug wise. I haven't loaded 4.20 yet either so I don't know if
that helps. Apparently it doesn as the description below is pretty
close to what I was seeing. I think it is a realtime/linux issue the
machine ran the distro find until an attempt to run EMc is made.
Thanks
Dave
Jon Elson wrote:
>nwlinfo wrote:
>
>
>
>>Greetings, I am having difficulties with the installation process
>>for EMC/Debian combo (BDI-4.20) on a 5 yr old P3 w/ 512MB ram. The
>>hard disk (about 8 GB) has been reformated and there should be no
>>partitions. From what I can tell, my downloaded copy from
>>www.wildrice.com/emc is probably okay (because checksum matches),
>>and the CD initially boots. When the initial screen loads, I hit
>>enter to continue. After a couple minutes into the installation, a
>>dialog box warns that the hard disk drive cannot be found. I
>>believe a driver was automatically loaded a little earlier during
>>the installation (aic-7xxx driver), but it must be causing some
>>problem. The computer has an Adaptec AIC-7899 SCSI controller.
>>
>>
>>
>>
>Is SCSI supported on the 4.xx BDI's? I know it was NOT supported
>on earlier BDI versions. This aic7xxx driver may be loading, but it
>may not be a driver acceptable for the OS disk.
>
>Do you ever get to the create partitions screen? (I'm guessing it is
>getting stuck just before that point. There may be a tricky command
>option that will allow you to tell it that a SCSI hard drive will be used
>instead of IDE.)
>
>Jon
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
>
>
Discussion Thread
nwlinfo
2005-08-03 14:21:42 UTC
BDI-4.20 Software Installation
Alan Marconett
2005-08-03 14:54:03 UTC
[Spam] RE: [CAD_CAM_EDM_DRO] BDI-4.20 Software Installation
Max
2005-08-03 15:38:45 UTC
Re: [CAD_CAM_EDM_DRO] BDI-4.20 Software Installation
Jon Elson
2005-08-03 17:16:19 UTC
Re: [CAD_CAM_EDM_DRO] BDI-4.20 Software Installation
David A. Frantz
2005-08-03 20:30:37 UTC
Re: [CAD_CAM_EDM_DRO] BDI-4.20 Software Installation
Tom Hubin
2005-08-04 12:16:11 UTC
Re: [CAD_CAM_EDM_DRO] BDI-4.20 Software Installation
North Western Limited
2005-08-05 06:57:23 UTC
BDI-4.20 Software Installation (still having problems)