Re: Looking for EDM wire
Posted by
turbulatordude
on 2005-09-06 10:01:45 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Andrey Lipavsky"
<alipavsky@c...> wrote:
place to start.
Since I would be using short lenghts, 1mm exposed or so, I don't think
it should be terribly hard to find something.
Dave
<alipavsky@c...> wrote:
> Dave,hobby
> Have you considered the piano wire (spring steel) available at most
> shops? It's spring-hardened and would be a good candidate to test with.usually
> I've bought pieces in diameters down to 0.015", maybe smaller. It
> comes in 36" lengths and is a buck or two per section.I'm hoping to get into the 0.005 inch range, but that is a decent
>
> My two cents worth...
> Andrey
place to start.
Since I would be using short lenghts, 1mm exposed or so, I don't think
it should be terribly hard to find something.
Dave
>reach it if
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of turbulatordude
> Sent: Tuesday, September 06, 2005 11:47 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Looking for EDM wire
>
> Hi all,
>
> I'm trying to get my ducts lined up for a plunge EDM I'm building from
> the new Ben Flemming book.
>
> I'd like to get my hands on a few feet of EDM wire of different sizes
> and types to test them out.
>
> It is NOT a wire EDM machine, but I am looking to use EDM wire to poke
> small holes in sheet metal and maybe slots if the wire can be used
> that way.
>
> Anyone know where I can get a few feet of different types of wire ?
>
> Also, it looks as though there are different hardnesses of wire.
> since this would be a plunge unit, hard would be desired.
>
>
> Dave
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@a...,
> timg@k...
> Moderator: pentam@c... indigo_red@q... davemucha@j...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> you have trouble.there, for OT
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are
> subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
Discussion Thread
turbulatordude
2005-09-06 08:47:22 UTC
Looking for EDM wire
Andrey Lipavsky
2005-09-06 08:51:38 UTC
RE: [CAD_CAM_EDM_DRO] Looking for EDM wire
turbulatordude
2005-09-06 10:01:45 UTC
Re: Looking for EDM wire
jesse Brennan
2005-09-06 10:37:53 UTC
Re: [CAD_CAM_EDM_DRO] Looking for EDM wire
Andrey Lipavsky
2005-09-06 15:24:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire
JanRwl@A...
2005-09-06 16:39:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire
Thos J Powderly
2005-09-07 06:32:15 UTC
Looking for EDM wire
turbulatordude
2005-09-07 06:52:22 UTC
Re: Looking for EDM wire
Andrey Lipavsky
2005-09-07 07:56:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire
Marcus
2005-09-07 09:01:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire
Elliot Burke
2005-09-07 10:25:31 UTC
RE:Looking for EDM wire
R Rogers
2005-09-07 10:35:39 UTC
Re: [CAD_CAM_EDM_DRO] RE:Looking for EDM wire
Raymond Heckert
2005-09-07 19:07:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire
Zafar Salam
2005-09-08 08:43:21 UTC
Re: [CAD_CAM_EDM_DRO] Looking for EDM wire
turbulatordude
2005-09-08 09:05:56 UTC
Re: Looking for EDM wire
john_glynn57
2005-09-09 10:16:52 UTC
Re: Looking for EDM wire