CAD CAM EDM DRO - Yahoo Group Archive

Re: Looking for EDM wire

Posted by john_glynn57
on 2005-09-09 10:16:52 UTC
SINKING
GRAPHITE FOR COMPLEX FORMS AND LARGE ELECTRODES
COPPER FOR SPEED
TUNGSTEN COPPER FOR GEOMETRY
HOLE DRILLING IS GENERALLY PRECISION COPPER TUBE

WIRE
BRASS IS GENERALLY USED POSSIBLY BECAUSE COPPER IS TOO SOFT
HARDENED BRASS IS USED FOR ADDITIONAL PRECISION AS THE WIRE BOWS
LESS WHEN CORNERING
0.25mm IS THE DIAMETER FOR BEST OVERALL PERFORMANCE
ZINC COATED BRASS IS USED FOR ADDITIONAL SPEED AS THE ZINC IS
IGNITED IN THE PLASMA AND ADDS ADDITIONAL ENERGY TO THE SPARK
SMALL DIAMETER WIRES ARE ONLY USED FOR SPECIAL APPLICATIONS ALSO THE
SAME APPLIES FOR TUNGSTEN WIRES

OTHER
FLUSHING IS CRITICAL --- SPARK GENERATION CANNOT TAKE PLACE UNLESS
THE DEBRIS IS CLEARED. THIS IS CRITICAL FOR HOLE DRILLING

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Raymond Heckert" <jnr@a...>
wrote:
> Brass, because it's much stiffer than copper, and it conducts
current almost
> as well... me thinks, anyways.
>
> RayHex
>
> -----Original Message-----
> Date: Tuesday, September 06, 2005 4:39 PM
> Subject: Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire
>
>
> >
> >
> >Yes... I never did EDM, but I recall reading that "EDM Wire" is
supposed
> to
> >be BRASS wire. Why that? Why not lead or rhodium? (Joking,
but still
> >asking a serious question!)
> >

Discussion Thread

turbulatordude 2005-09-06 08:47:22 UTC Looking for EDM wire Andrey Lipavsky 2005-09-06 08:51:38 UTC RE: [CAD_CAM_EDM_DRO] Looking for EDM wire turbulatordude 2005-09-06 10:01:45 UTC Re: Looking for EDM wire jesse Brennan 2005-09-06 10:37:53 UTC Re: [CAD_CAM_EDM_DRO] Looking for EDM wire Andrey Lipavsky 2005-09-06 15:24:37 UTC RE: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire JanRwl@A... 2005-09-06 16:39:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire Thos J Powderly 2005-09-07 06:32:15 UTC Looking for EDM wire turbulatordude 2005-09-07 06:52:22 UTC Re: Looking for EDM wire Andrey Lipavsky 2005-09-07 07:56:29 UTC RE: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire Marcus 2005-09-07 09:01:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire Elliot Burke 2005-09-07 10:25:31 UTC RE:Looking for EDM wire R Rogers 2005-09-07 10:35:39 UTC Re: [CAD_CAM_EDM_DRO] RE:Looking for EDM wire Raymond Heckert 2005-09-07 19:07:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Looking for EDM wire Zafar Salam 2005-09-08 08:43:21 UTC Re: [CAD_CAM_EDM_DRO] Looking for EDM wire turbulatordude 2005-09-08 09:05:56 UTC Re: Looking for EDM wire john_glynn57 2005-09-09 10:16:52 UTC Re: Looking for EDM wire