CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver

Posted by Jon Elson
on 2005-10-02 14:14:02 UTC
Blue wrote:

>Hi Jon,
>
>If I decide to us the better circuit with the opto-isolation and the FET's
>IRF630's (needing 10volts to trigger it full on) could you spoon feed me
>with a diagram corrected with the addition of the fast diodes you suggest? I
>can send you a diagram.
>
>I also notice the motor direction CW and CCW are two pins whereas most
>drivers use only one pin, how can this be altered.
>
>
The circuit would have something like a 100 Ohm 3 W resistor connected
to the power supply. The other end would be connected to the cathode of
two fast power diodes (the end with the bar). The diode anodes would be
connected to the two motor terminals where they connect to the transistor
drain terminals. The 100 Ohm resistor and a 1 A winding current would
limit the voltage on the transistors to 100 V. You also need a 20 Ohm, 25 W
resistor in series with each motor common wire to limit motor current
to 1 A with a 20 V power supply.

This circuit http://jelinux.pico-systems.com/images/stepdir.pdf will
generate
the motor phase pulses from step and dir signals.

Jon

Discussion Thread

Blue 2005-10-01 08:35:36 UTC Stepper Motor Driver KM6VV 2005-10-01 09:00:53 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver turbulatordude 2005-10-01 09:30:36 UTC Re: Stepper Motor Driver Jon Elson 2005-10-01 10:22:56 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Blue 2005-10-01 11:37:40 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver juan gelt 2005-10-01 11:51:15 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver John Dammeyer 2005-10-01 12:35:05 UTC RE: [CAD_CAM_EDM_DRO] Stepper Motor Driver turbulatordude 2005-10-01 12:48:48 UTC Re: Stepper Motor Driver Blue 2005-10-01 13:07:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver Blue 2005-10-01 13:07:45 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver turbulatordude 2005-10-01 13:24:44 UTC Re: Stepper Motor Driver Blue 2005-10-01 13:46:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver juan gelt 2005-10-01 14:48:09 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Jon Elson 2005-10-01 15:00:08 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver juan gelt 2005-10-01 15:02:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver Blue 2005-10-01 15:04:15 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Jon Elson 2005-10-01 15:10:26 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Jon Elson 2005-10-01 15:18:19 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver juan gelt 2005-10-01 16:31:10 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver turbulatordude 2005-10-01 17:06:14 UTC Re: Stepper Motor Driver Paul Kelly 2005-10-01 17:27:08 UTC RE: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver juan gelt 2005-10-01 19:53:56 UTC RE: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver Paul Kelly 2005-10-01 20:42:49 UTC RE: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver Jon Elson 2005-10-01 20:55:40 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver juan gelt 2005-10-01 21:08:02 UTC RE: [CAD_CAM_EDM_DRO] Re: Stepper Motor Driver juan gelt 2005-10-01 21:18:19 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Blue 2005-10-02 04:53:54 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver turbulatordude 2005-10-02 10:52:44 UTC Re: Stepper Motor Driver Jon Elson 2005-10-02 14:01:05 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Jon Elson 2005-10-02 14:14:02 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver juan gelt 2005-10-02 20:52:03 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Blue 2005-10-03 07:56:38 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Roy J. Tellason 2005-10-03 08:50:34 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver Blue 2005-10-03 09:10:14 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Driver