Re: MSA 665 linear Encoder
Posted by
linearmeasurement
on 2005-11-24 08:43:00 UTC
Thomas,
I am not sure which connector you have on the end of the signal cable
so I can give you the pin-outs for the RSF standard connector.
L70 Din
Pin 1 - Ground
Pin 2 - Not used
Pin 3 - A
Pin 4 - B
Pin 5 - 5 volts
Pin 6 - Reference Index
Pin 7 - Shield
Regards,
Tim Barnard
LMSC
I am not sure which connector you have on the end of the signal cable
so I can give you the pin-outs for the RSF standard connector.
L70 Din
Pin 1 - Ground
Pin 2 - Not used
Pin 3 - A
Pin 4 - B
Pin 5 - 5 volts
Pin 6 - Reference Index
Pin 7 - Shield
Regards,
Tim Barnard
LMSC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Thomas" <teecee@c...> wrote:
>
> Hi all
> I 'm fresh meat here in this forum and I would like to ask for some
help with a linear Encoder that I recently picked up, its a MSA655
linear Encoder without a Plug connection on the cable, if anyone is
able to give details for the Wiring diagram +5V, Gnd, ChA, ChB.
>
> There is a red & Black wire perhaps thats +5V & Gnd if that can be
confirmed I'm sure I could figure the rest out using the Scope.
> btw I have had no replies from RSF Elektronik .
>
> PN Code: 82277804
> No: 081-0308430110
> Grating: 0.04mm
> MSA: 665
> Spec: 5F
> Zero ref Pulse: 7
>
> TIA
> Regards
> Thomas
>
> [Non-text portions of this message have been removed]
>
Discussion Thread
Thomas
2005-11-23 10:10:43 UTC
MSA 665 linear Encoder
linearmeasurement
2005-11-24 08:43:00 UTC
Re: MSA 665 linear Encoder
Thomas
2005-11-24 21:08:12 UTC
MSA 665 linear Encoder
Steve Haushahn
2005-11-25 04:54:54 UTC
Re: [CAD_CAM_EDM_DRO] MSA 665 linear Encoder
Dave Shiels
2005-11-25 08:41:20 UTC
Re: [CAD_CAM_EDM_DRO] MSA 665 linear Encoder
Steve Haushahn
2005-11-25 09:27:31 UTC
Re: [CAD_CAM_EDM_DRO] MSA 665 linear Encoder
Dave Shiels
2005-11-25 13:01:14 UTC
Re: [CAD_CAM_EDM_DRO] MSA 665 linear Encoder
KM6VV
2005-11-25 17:50:46 UTC
Re: [CAD_CAM_EDM_DRO] MSA 665 linear Encoder
Thomas
2005-11-26 07:47:46 UTC
Re: [CAD_CAM_EDM_DRO] MSA 665 linear Encoder
Crs Hawk
2005-11-29 10:28:16 UTC
[CAD_CAM_EDM_DRO] Stepper motors move wrong direction.
Stephen Wille Padnos
2005-11-29 10:48:00 UTC
Re: [CAD_CAM_EDM_DRO] Stepper motors move wrong direction.
Les Newell
2005-11-29 11:00:10 UTC
Isel C142 codes
Crs Hawk
2005-11-29 11:19:31 UTC
Re: [CAD_CAM_EDM_DRO] Isel C142 codes
Les Newell
2005-11-29 13:26:20 UTC
Re: [CAD_CAM_EDM_DRO] Isel C142 codes
Dave Fisher
2005-11-29 14:10:30 UTC
RE: [CAD_CAM_EDM_DRO] Stepper motors move wrong direction.