CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Z axis drive

Posted by Anders Wallin
on 2006-01-05 08:22:38 UTC
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Ron Ginger <ronginger@a...>
> wrote:
> >
> > Im doing a conversion on a large, square column, mill, like a RF-45,
> but
> > from Wholesale Tool
> Ron:
>
> I converted the same mill (ZX7045), but did not use the quill
> for the Z axis . Check it out at:
> http://www.geocities.com/wuksta/ZX7045.html
> Gerry

Interesting ! have been thinking about converting this size mill myself...

What travels do you have ?

Your site seems down due to high traffic...

The one picture I downloaded seemed to indicate you use linear-rails
insted of the dovetail ways usually found on these mills ? Have you
retrofitted ballscrews also ?

AW

Discussion Thread

Brian Fairey 1999-08-01 04:17:17 UTC Z axis drive Dan Falck 1999-08-01 05:32:47 UTC Re: Z axis drive Ron Ginger 2006-01-05 05:02:28 UTC Z axis drive Les Newell 2006-01-05 05:20:59 UTC Re: [CAD_CAM_EDM_DRO] Z axis drive Ken Strauss 2006-01-05 05:51:47 UTC RE: [CAD_CAM_EDM_DRO] Z axis drive kmslinda 2006-01-05 08:00:39 UTC Re: Z axis drive Anders Wallin 2006-01-05 08:22:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive Jon Elson 2006-01-05 09:45:48 UTC Re: [CAD_CAM_EDM_DRO] Z axis drive Art Eckstein 2006-01-05 10:14:49 UTC Re: [CAD_CAM_EDM_DRO] Z axis drive jesse Brennan 2006-01-05 11:16:09 UTC Re: [CAD_CAM_EDM_DRO] Z axis drive n1ych 2006-01-05 13:44:17 UTC Re: Z axis drive Anders Wallin 2006-01-05 13:55:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive kmslinda 2006-01-05 14:24:59 UTC Re: Z axis drive kmslinda 2006-01-05 14:30:26 UTC Re: Z axis drive spc_aux 2006-01-05 15:53:23 UTC Re: Z axis drive JCullins 2006-01-05 17:51:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive Ron Ginger 2006-01-05 18:35:45 UTC Re: Z axis drive skykotech 2006-01-05 20:44:06 UTC Re: Z axis drive gary 2006-01-05 21:37:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive spc_aux 2006-01-06 05:50:46 UTC Re: Z axis drive spc_aux 2006-01-06 05:55:58 UTC Re: Z axis drive skykotech 2006-01-06 08:02:41 UTC Re: Z axis drive gary 2006-01-06 08:58:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive R Rogers 2006-01-06 10:03:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive spc_aux 2006-01-06 10:47:42 UTC Re: Z axis drive George Taylor, IV 2006-01-06 11:17:05 UTC RE: [CAD_CAM_EDM_DRO] Re: Z axis drive R Rogers 2006-01-06 11:57:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive Dan Mauch 2006-01-06 12:05:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Z axis drive spc_aux 2006-01-06 15:36:34 UTC Re: Z axis drive spc_aux 2006-01-06 15:47:47 UTC Re: Z axis drive wthomas@g... 2006-01-07 21:35:54 UTC W.E.T.[CAD_CAM_EDM_DRO] Re: Z axis drive gary 2006-01-08 13:54:43 UTC Re: W.E.T.[CAD_CAM_EDM_DRO] Re: Z axis drive longassscreenname 2006-01-14 13:01:17 UTC Re: Z axis drive