Lathe solid model to G code
Posted by
wanliker@a...
on 2006-03-26 21:07:49 UTC
In a message dated 3/24/2006 5:32:36 PM Mountain Standard Time,
imserv@... writes:
Have you seen this Bill?
http://www.vectorcad3d.com/support/Lathedrawingmode.htm
Yes, Fred I looked at it, and the Large X and Z looks a bit overdone. Yes,
Vector can do it, but look at the contortions you had to go thru to do it.
IMHO, one should be just able to click New, then click Lathe, and it is
properly implemented..... Or something equally simple. Using Lathe, in any
program should be completely seamless in all respects if properly done in the
first place.
The ability to do something, does not mean that it was properly implemented
in the first place.
Thanks,
bill
[Non-text portions of this message have been removed]
imserv@... writes:
Have you seen this Bill?
http://www.vectorcad3d.com/support/Lathedrawingmode.htm
Yes, Fred I looked at it, and the Large X and Z looks a bit overdone. Yes,
Vector can do it, but look at the contortions you had to go thru to do it.
IMHO, one should be just able to click New, then click Lathe, and it is
properly implemented..... Or something equally simple. Using Lathe, in any
program should be completely seamless in all respects if properly done in the
first place.
The ability to do something, does not mean that it was properly implemented
in the first place.
Thanks,
bill
[Non-text portions of this message have been removed]
Discussion Thread
roboticscnc
2006-03-23 04:47:34 UTC
Lathe solid model to G code
Fred Smith
2006-03-23 11:12:06 UTC
Re: Lathe solid model to G code
kiwiavi
2006-03-23 13:02:18 UTC
Re: Lathe solid model to G code
wanliker@a...
2006-03-23 13:46:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code
wanliker@a...
2006-03-23 13:47:19 UTC
Lathe solid model to G code
Fred Smith
2006-03-24 16:31:58 UTC
Re: Lathe solid model to G code
Fred Smith
2006-03-25 09:12:14 UTC
Re: Lathe solid model to G code
Steve Blackmore
2006-03-26 00:13:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code
Fred Smith
2006-03-26 00:55:37 UTC
Re: Lathe solid model to G code
Steve Blackmore
2006-03-26 02:52:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code
Fred Smith
2006-03-26 07:43:20 UTC
Re: Lathe solid model to G code
Fred Smith
2006-03-26 07:55:46 UTC
Re: Lathe solid model to G code
turbulatordude
2006-03-26 08:08:03 UTC
Re: Lathe solid model to G code
Fred Smith
2006-03-26 09:31:19 UTC
Re: Lathe solid model to G code
Tony Jeffree
2006-03-26 12:07:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code
Fred Smith
2006-03-26 12:38:52 UTC
Re: Lathe solid model to G code
Torleif Jensen
2006-03-26 13:47:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code
wanliker@a...
2006-03-26 15:07:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code
wanliker@a...
2006-03-26 21:07:49 UTC
Lathe solid model to G code
Fred Smith
2006-03-27 06:45:01 UTC
Re: Lathe solid model to G code
wanliker@a...
2006-03-27 10:36:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Lathe solid model to G code