Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!

I seen a similar air stunt, It was many years ago at the Abbottsford
Air Show. The Russians brought over a few MIG 29's, and of course
all the air force pilots were having a good gawk at them. They then
offered to let a pilot fly the trainer, but by drawing from a hat, of
course
the Canadian pilots won that draw, and left the US pilots crying in
thier beer. The front cockpit in this aircraft was gutted, except for
the basic flight controls, that did not require any legends.

Steve

----------
From: Doug Yeager <doug@...>
To: CAD_CAM_EDM_DRO@egroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Date: Tuesday, July 04, 2000 8:16 AM

hi carey,

as far as a direct discount i can't really do that because it wouldn't be
enough of a discount to be worth anyones while. there is a quantity
discount but that doesn't really pertain to this message board clientele
either. this message board has done quite a bit for the hobby/home
shop/automation industry though it seems and deserves some perks that go
along with it. i used to put cncpro and ACEconverter on ebay quite a bit
although i haven't in the past couple months. i started the bidding at
about 35-40% discount and quite frequently it went for that with just a
couple bids or so. the next time i put a couple licenses up on ebay i will

notify the group first so that they know it is there.

and have a great 4th.....i'm very proud to be an american (saw a recent
airshow at travis airforce base two days ago and saw an f-15 fly by 3 times

and accelerate out of site completely vertical...never been so proud of my
country)

cheers,
-doug

At 10:46 AM 7/4/00 -0400, you wrote:

>Doug: Well, here it comes get ready to duck. Any thoughts as to
>discounting CNCPro to list members? I hope that I don't scare you off
>with that question. And ,yes, I do know the meaning of the word NO. It
>doesn't hurt to ask does it? There are a few of us CNC converting- ebay
>junkies on this list that are about tapped out and I have to say that
>software gets pushed to the bottom of the pile of things to buy. I, for
>one, am about brain dead trying to figure all of these things out and
>an EMC install would push me over the edge. I hope that the tear drops
>don' t short out my keyboard.
>Have an enjoyable 4th of July!
>
>
>------------------------------------------------------------------------
>0% Introductory APR!
>Instant Approval!
>Aria Visa - get yours today.
>http://click.egroups.com/1/6035/4/_/423600/_/962722063/
>------------------------------------------------------------------------
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager

------------------------------------------------------------------------
0% Introductory APR!
Instant Approval!
Aria Visa - get yours today.
http://click.egroups.com/1/6035/4/_/423600/_/962723519/
------------------------------------------------------------------------

Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@egroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
Moderator: jmelson@... [Moderator]
URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
FAQ: http://www.ktmarketing.com/faq.html
bill,
List Manager