CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!

Posted by Mike Rainone
on 2000-07-04 20:53:31 UTC
Thank you, Matt, I will. Mooooo.

Mike Rainone

Matt Shaver wrote:

> > From: Mike Rainone <mrain1@...>
> > Finally, Tim, if you wouldn't mind, I will try the Linux install. I have
> plenty of room on the shop box 1 gig drive, and will buy a
> > version of Red Hat, just for the support. My thinking is this, while I have
> caused a bunch of trouble for this group, I am within
> > two months of chasing down a Boss "x" and doing a retrofit. I think you,
> Tim, said that Matt Shaver was doing these or was a good
> > source of info.
>
> I've done one anyway, here's a little info:
>
> http://users.erols.com/mshaver/bps1.htm
>
> There are a few problems with using the EMC to control stepper systems that
> run at high speed. The machine in the picture would only rapid at 54 ipm
> reliably, and with .00025" steps that works out to a step frequency of 3600
> Hz. In retrospect (and that's the only way I can look at this machine as I
> sold it and the new owner is happy with it), I might have wired the motors
> differently and gotten better performance.
>
> I'm not a fast typist, so if you'd like to know more about how this machine
> was put together you can read some of my old messages in the archive, or give
> me a call at your convenience.
>
> Thanks,
>
> Matt Shaver
> (410) 521-3715
>
> I never saw a purple cow
> I never hope to see one
> But I can tell you anyhow
> I'd rather see than be one!.
> -- Gelett Burgess
>
> http://www.notfrisco.com/calmem/burgess.html
>
> ------------------------------------------------------------------------
> Life's too short to send boring email. Let SuperSig come to the rescue.
> http://click.egroups.com/1/6137/4/_/423600/_/962768154/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager

Discussion Thread

Mike Rainone 2000-07-02 15:24:18 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Bob Campbell 2000-07-02 16:03:52 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Anderson 2000-07-02 16:10:32 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Doug Fortune 2000-07-02 16:35:10 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Mike Rainone 2000-07-02 16:42:04 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Tim Goldstein 2000-07-02 16:46:29 UTC RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Mike Rainone 2000-07-02 16:48:30 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Mike Rainone 2000-07-02 17:03:14 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Tim Goldstein 2000-07-02 17:13:55 UTC RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Anderson 2000-07-02 18:31:22 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! johndroc@a... 2000-07-02 18:32:32 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Tim Goldstein 2000-07-02 20:06:23 UTC RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Tim Goldstein 2000-07-02 20:07:52 UTC RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Anderson 2000-07-02 21:14:05 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Elson 2000-07-02 21:30:10 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Elson 2000-07-02 21:38:20 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Elson 2000-07-02 22:27:36 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Mike Rainone 2000-07-03 21:53:10 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Doug Yeager 2000-07-04 06:18:14 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Carey L. Culpepper 2000-07-04 07:47:42 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Doug Yeager 2000-07-04 08:11:59 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Carey L. Culpepper 2000-07-04 08:31:12 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Anderson 2000-07-04 10:10:44 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Steve Carlisle 2000-07-04 16:25:44 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Hugh Prescott 2000-07-04 16:49:01 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Anderson 2000-07-04 17:10:28 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Hugh Prescott 2000-07-04 17:27:37 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Matt Shaver 2000-07-04 20:35:53 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Mike Rainone 2000-07-04 20:53:31 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Elson 2000-07-04 21:55:54 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Jon Elson 2000-07-04 22:26:23 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! William Scalione 2000-07-05 00:11:02 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it! Mike Rainone 2000-07-05 07:12:51 UTC Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!