Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Posted by
Matt Shaver
on 2000-07-04 20:35:53 UTC
> From: Mike Rainone <mrain1@...>plenty of room on the shop box 1 gig drive, and will buy a
> Finally, Tim, if you wouldn't mind, I will try the Linux install. I have
> version of Red Hat, just for the support. My thinking is this, while I havecaused a bunch of trouble for this group, I am within
> two months of chasing down a Boss "x" and doing a retrofit. I think you,Tim, said that Matt Shaver was doing these or was a good
> source of info.I've done one anyway, here's a little info:
http://users.erols.com/mshaver/bps1.htm
There are a few problems with using the EMC to control stepper systems that
run at high speed. The machine in the picture would only rapid at 54 ipm
reliably, and with .00025" steps that works out to a step frequency of 3600
Hz. In retrospect (and that's the only way I can look at this machine as I
sold it and the new owner is happy with it), I might have wired the motors
differently and gotten better performance.
I'm not a fast typist, so if you'd like to know more about how this machine
was put together you can read some of my old messages in the archive, or give
me a call at your convenience.
Thanks,
Matt Shaver
(410) 521-3715
I never saw a purple cow
I never hope to see one
But I can tell you anyhow
I'd rather see than be one!.
-- Gelett Burgess
http://www.notfrisco.com/calmem/burgess.html
Discussion Thread
Mike Rainone
2000-07-02 15:24:18 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Bob Campbell
2000-07-02 16:03:52 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Anderson
2000-07-02 16:10:32 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Doug Fortune
2000-07-02 16:35:10 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Mike Rainone
2000-07-02 16:42:04 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Tim Goldstein
2000-07-02 16:46:29 UTC
RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Mike Rainone
2000-07-02 16:48:30 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Mike Rainone
2000-07-02 17:03:14 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Tim Goldstein
2000-07-02 17:13:55 UTC
RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Anderson
2000-07-02 18:31:22 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
johndroc@a...
2000-07-02 18:32:32 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Tim Goldstein
2000-07-02 20:06:23 UTC
RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Tim Goldstein
2000-07-02 20:07:52 UTC
RE: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Anderson
2000-07-02 21:14:05 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Elson
2000-07-02 21:30:10 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Elson
2000-07-02 21:38:20 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Elson
2000-07-02 22:27:36 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Mike Rainone
2000-07-03 21:53:10 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Doug Yeager
2000-07-04 06:18:14 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Carey L. Culpepper
2000-07-04 07:47:42 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Doug Yeager
2000-07-04 08:11:59 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Carey L. Culpepper
2000-07-04 08:31:12 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Anderson
2000-07-04 10:10:44 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Steve Carlisle
2000-07-04 16:25:44 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Hugh Prescott
2000-07-04 16:49:01 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Anderson
2000-07-04 17:10:28 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Hugh Prescott
2000-07-04 17:27:37 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Matt Shaver
2000-07-04 20:35:53 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Mike Rainone
2000-07-04 20:53:31 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Elson
2000-07-04 21:55:54 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Jon Elson
2000-07-04 22:26:23 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
William Scalione
2000-07-05 00:11:02 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!
Mike Rainone
2000-07-05 07:12:51 UTC
Re: [CAD_CAM_EDM_DRO] Maxnc - don't buy it!