CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] need axis design idea

Posted by davegsc@t...
on 2006-04-11 09:11:20 UTC
How about a stepping motor with an encoder, driving a cogged belt? Very
portable (just wrap it up to travel), and reasonably low-cost if you
drive it (and get the read-out) using a laptop. Set-up would be quick -
just run the idler out and clamp it.

Dave
Saltspring


-----Original Message-----
From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Elliot Burke
Sent: April 10, 2006 9:04 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] need axis design idea

A question about how to built a device: I need one axis with at least 8
feet
of travel. The load is very light, just a target. It does not need to
be
motorized, but some sort of position readout is required. Portable and
inexpensive are design goals. The accuracy of position readout isn't
very
high, 0.005 to 0.010" would be OK.

This is almost like one axis of a router. What is good practice there?

Thanks for any ideas you feel willing to share.

regards-
Elliot


--
Internal Virus Database is out-of-date.
Checked by AVG Free Edition.
Version: 7.1.385 / Virus Database: 268.3.1/291 - Release Date: 3/24/2006



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there,
for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links

Discussion Thread

Elliot Burke 2006-04-10 21:04:01 UTC need axis design idea wthomas@g... 2006-04-10 21:23:24 UTC W.E.T.Re: [CAD_CAM_EDM_DRO] need axis design idea wanliker@a... 2006-04-10 22:56:22 UTC need axis design idea wanliker@a... 2006-04-10 23:35:43 UTC need axis design idea davegsc@t... 2006-04-11 09:11:20 UTC RE: [CAD_CAM_EDM_DRO] need axis design idea shadi_salhab_78 2006-04-11 23:26:58 UTC Re: need axis design idea wanliker@a... 2006-04-11 23:37:38 UTC Re: [CAD_CAM_EDM_DRO] Re: need axis design idea Graham Stabler 2006-04-12 02:46:41 UTC Re: need axis design idea juan gelt 2006-04-12 05:35:40 UTC Re: [CAD_CAM_EDM_DRO] Re: need axis design idea Graham Stabler 2006-04-12 11:27:00 UTC Re: need axis design idea Elliot Burke 2006-04-15 19:18:23 UTC re: RE: need axis design idea G L Travis 2006-04-16 10:16:10 UTC Re: need axis design idea wanliker@a... 2006-04-16 10:38:57 UTC Re: [CAD_CAM_EDM_DRO] Re: need axis design idea G L Travis 2006-04-16 11:08:58 UTC Re: need axis design idea Lester Caine 2006-04-16 16:05:49 UTC Re: [CAD_CAM_EDM_DRO] Re: need axis design idea Graham Stabler 2006-04-16 17:03:59 UTC Re: need axis design idea juan gelt 2006-04-16 18:50:33 UTC Re: [CAD_CAM_EDM_DRO] Re: need axis design idea Lester Caine 2006-04-16 23:24:10 UTC Re: [CAD_CAM_EDM_DRO] Re: need axis design idea juangelt 2006-04-17 00:59:46 UTC Re: need axis design idea