Re: [CAD_CAM_EDM_DRO] Need help to decide what rack and pinion to use in a 6'x10' table
Posted by
Seiman H
on 2006-04-23 06:53:40 UTC
Hi Hector,
I can advice you with the following:
PA might play a role basically in load to avoid mechanical missing steps but it depends also what module are you using !!
I recommend module 1.5 PA 14.5 is enough with 4:1 gear ratio and 20 tooth on motor shaft facing 80 tooth on gear shaft and again 20 tooth on rack.
you must consider putting a higher gear ration if you looking for better cut quality.
now try to buy antibacklash rack and pinion and check for durability when select Carbon steel or stainless steel.
Let me know what will happen with you
Good Luck
seiman_h@...
Hector <hector_a_quintanilla@...> wrote:
Hello,
Im confused on which combination of rack and pinion to use for a
6'x10' table.
I know that there are three steps to solve.
1.- which presure angle (PA) to choose, 14.5 PA or 20 PA? I know the
20 PA will hold more load than 14.5 PA, but how much is more? does
this size of table really benefits using 20 PA? what is the
important facts to know to make this decision?
2.- after knowing what pressure angle will be used, the next step is
to decide the diametral pitch to use. So what is necesarry to
consider in this decision?
3.- In this step we already know the PA and DP we are going to use,
now comes to decide how many teeth on the pinion, so what governs
this decision?
Is hard to find some 20 PA conbinations i been suggested earlier. So
if this questions are really hard to explain, i'll be happy to have
some suggestions without explanation and where to buy them online. I
think is better if someone could really make clear this for me and
others, i guess other have the same doubts.
Kindest Regards,
Hector Quintanilla
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
---------------------------------
Make free worldwide PC-to-PC calls. Try the new Yahoo! Canada Messenger with Voice
[Non-text portions of this message have been removed]
I can advice you with the following:
PA might play a role basically in load to avoid mechanical missing steps but it depends also what module are you using !!
I recommend module 1.5 PA 14.5 is enough with 4:1 gear ratio and 20 tooth on motor shaft facing 80 tooth on gear shaft and again 20 tooth on rack.
you must consider putting a higher gear ration if you looking for better cut quality.
now try to buy antibacklash rack and pinion and check for durability when select Carbon steel or stainless steel.
Let me know what will happen with you
Good Luck
seiman_h@...
Hector <hector_a_quintanilla@...> wrote:
Hello,
Im confused on which combination of rack and pinion to use for a
6'x10' table.
I know that there are three steps to solve.
1.- which presure angle (PA) to choose, 14.5 PA or 20 PA? I know the
20 PA will hold more load than 14.5 PA, but how much is more? does
this size of table really benefits using 20 PA? what is the
important facts to know to make this decision?
2.- after knowing what pressure angle will be used, the next step is
to decide the diametral pitch to use. So what is necesarry to
consider in this decision?
3.- In this step we already know the PA and DP we are going to use,
now comes to decide how many teeth on the pinion, so what governs
this decision?
Is hard to find some 20 PA conbinations i been suggested earlier. So
if this questions are really hard to explain, i'll be happy to have
some suggestions without explanation and where to buy them online. I
think is better if someone could really make clear this for me and
others, i guess other have the same doubts.
Kindest Regards,
Hector Quintanilla
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
---------------------------------
Make free worldwide PC-to-PC calls. Try the new Yahoo! Canada Messenger with Voice
[Non-text portions of this message have been removed]
Discussion Thread
Hector
2006-04-21 17:14:27 UTC
Need help to decide what rack and pinion to use in a 6'x10' table
turbulatordude
2006-04-22 07:09:53 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Seiman H
2006-04-23 06:53:40 UTC
Re: [CAD_CAM_EDM_DRO] Need help to decide what rack and pinion to use in a 6'x10' table
ballendo
2006-04-23 08:44:07 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Hector
2006-04-23 16:35:54 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
turbulatordude
2006-04-23 18:57:14 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Jarrett & Heidi Johnson
2006-04-23 19:27:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need help to decide what rack and pinion to use in a 6'x10' table
Jarrett & Heidi Johnson
2006-04-23 19:32:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need help to decide what rack and pinion to use in a 6'x10' table
Les Newell
2006-04-24 01:50:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need help to decide what rack and pinion to use in a 6'x10' table
Hector
2006-04-25 16:12:23 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Jarrett & Heidi Johnson
2006-04-25 17:31:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need help to decide what rack and pinion to use in a 6'x10' table
turbulatordude
2006-04-25 20:23:07 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Hector
2006-04-26 09:00:48 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Heidi Johnson
2006-04-26 09:22:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need help to decide what rack and pinion to use in a 6'x10' table
Hector
2006-04-26 14:12:35 UTC
Re: Need help to decide what rack and pinion to use in a 6'x10' table
Heidi Johnson
2006-04-26 15:18:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need help to decide what rack and pinion to use in a 6'x10' table