Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Posted by
Charles VanLeeuwen
on 2000-07-06 13:16:39 UTC
To make use of the higher 440 volt rating, you have to run a single phase
step up transformer on the 220 volt single phase input in front of the
inverter and you have to change the motor wiring to run at 440 (almost all 3
phase motors can be run at 220 or 440 depending on how the leads are
connected).
step up transformer on the 220 volt single phase input in front of the
inverter and you have to change the motor wiring to run at 440 (almost all 3
phase motors can be run at 220 or 440 depending on how the leads are
connected).
> These units do not convert voltage. You run 240 V motors with a 240 Vdiscussion of shop built systems, for CAD, CAM, EDM, and DRO.
> input,
> and a 240 V rated inverter. You run 440 V motors with a 440 V input,
> and a
> 440 V inverter. In theory, you could run a 240 V motor from a 440 V
> inverter
> with 440 V input, and program the motor for 240 V at 60 Hz. But, you'd
> need a 2 Hp inverter to run a 1 Hp motor, as the current doubles when
> the
> rated voltage drops to half. Just look at the rated current on the
> nameplate
> of a dual voltage motor. Also, the 240 V motor has 1/4th the inductance
> of
> a 440 V motor, so the PWM peak current will not come out right at all
> for
> a 440 V inverter running a 240 V motor, and you would likely get false
> overcurrent trips. So, you really get no benefit, and will pay extra,
> to be
> back where you started from.
>
> Jon
>
>
> ------------------------------------------------------------------------
> Who invented Gatorade -- and what part did it play in
> winning the1967 Orange Bowl? Find out the true facts at
> http://click.egroups.com/1/6212/4/_/423600/_/962860459/
> ------------------------------------------------------------------------
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>
Discussion Thread
Darrell
2000-07-05 17:49:08 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-05 18:30:58 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Doug Harrison
2000-07-05 18:35:06 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Darrell
2000-07-05 18:39:11 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Doug Harrison
2000-07-05 19:12:34 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-05 20:07:36 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-05 20:12:22 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
ptengin@a...
2000-07-05 21:08:18 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Jon Elson
2000-07-05 22:14:19 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Darrell
2000-07-05 22:21:05 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Larry Van Duyn
2000-07-06 06:19:42 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
ptengin@a...
2000-07-06 12:00:08 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-06 13:11:26 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-06 13:16:39 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-06 13:19:08 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Charles VanLeeuwen
2000-07-06 13:21:19 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Jon Elson
2000-07-06 15:20:19 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters
Doug Harrison
2000-07-06 15:50:32 UTC
Re: [CAD_CAM_EDM_DRO] Inverters/phase converters