CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] wire for motor ?

Posted by Dave Halliday
on 2006-12-10 20:54:18 UTC
A good wire chart is here:
http://www.powerstream.com/Wire_Size.htm

28 Gage's limit is about 1.4 Amps -- you need to go to 24 Gage to handle 3.5
Amps and even then, I would bump it up to 16 as you will probably be using
stranded wire (less ampacity) and this gives you a nice buffer against
surges and overloads. You want the fuze to blow, not your cable.

Any electronic place will sell you a nice braided plastic sleeve that you
can slip your wires through to make a neat cable. Alternately, you can buy
50 feet of some multi-conductor and roll your own.

Dave

> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of turbulatordude
> Sent: Sunday, December 10, 2006 8:56 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] wire for motor ?
>
>
> Hi all,
>
> I used a db9 connector for an connector on my SLA7062 driver. I hope
> to use 34 volts and up to 3 amps.
>
> I was hoping to also use a store bought db9 cable. Unfortunatly,
> they seem to not have any wire ga listed (wadda-ya want for $1.99)
> but it seems that 28ga is common.
>
> The question is about wire rating.
>
> how do you rate wire when using a stepper that has a chopper or PWM
> circuit ?
>
> If the motor is 3 volts and 3 amps, is the total wire wattage
> 9 watts ?
>
> Dave
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com
> to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider
> this to be a sister site to the CCED group, as many of the
> same members are there, for OT subjects, that are not allowed
> on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
> EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>

Discussion Thread

turbulatordude 2006-12-10 09:00:09 UTC wire for motor ? turbulatordude 2006-12-10 09:17:20 UTC Re: wire for motor ? John Dammeyer 2006-12-10 09:30:29 UTC RE: [CAD_CAM_EDM_DRO] wire for motor ? James Washer 2006-12-10 09:57:00 UTC Re: [CAD_CAM_EDM_DRO] wire for motor ? Stephen Wille Padnos 2006-12-10 10:56:28 UTC Re: [CAD_CAM_EDM_DRO] wire for motor ? John Dammeyer 2006-12-10 11:54:35 UTC RE: [CAD_CAM_EDM_DRO] wire for motor ? Tom Hubin 2006-12-10 13:38:15 UTC Re: [CAD_CAM_EDM_DRO] wire for motor ? cnc002@a... 2006-12-10 15:45:35 UTC Re: [CAD_CAM_EDM_DRO] wire for motor ? turbulatordude 2006-12-10 18:17:27 UTC Re: wire for motor ? John Hansford 2006-12-10 18:49:10 UTC Re: wire for motor ? cnc002@a... 2006-12-10 19:02:36 UTC Re: [CAD_CAM_EDM_DRO] Re: wire for motor ? Jon Elson 2006-12-10 19:10:53 UTC Re: [CAD_CAM_EDM_DRO] Re: wire for motor ? turbulatordude 2006-12-10 20:28:52 UTC Re: wire for motor ? John Hansford 2006-12-10 20:49:34 UTC Re: wire for motor ? Dave Halliday 2006-12-10 20:54:18 UTC RE: [CAD_CAM_EDM_DRO] wire for motor ? JanRwl@A... 2006-12-10 21:45:27 UTC Re: [CAD_CAM_EDM_DRO] Re: wire for motor ? Lawrence Gran 2006-12-11 14:12:00 UTC Re: wire for motor ? John Dammeyer 2006-12-12 11:28:35 UTC Shumatech DRO Lester Caine 2006-12-12 11:38:14 UTC Re: [CAD_CAM_EDM_DRO] Shumatech DRO