CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] 5HP VFD

Posted by Mark Vaughan
on 2007-02-10 09:04:27 UTC
Look on ebay for a UK firm called Drives direct in Nottingham, run by the
family of a guy called David.

They exclusively offer Teco drives where they have the software to convert
larger three phase input VFD’s to accept a single phase supply.



Many other larger drives can be converted by using an drive, feeding two
phase into two phase’s and making it think the third is present by
connecting it via a capacitor.

The over rating is to save the input rectifier which has to handle all power
down two lines instead of three.



Also some VFD’s will only produce the same three phase output voltage as the
single supplied, i.e. 240V single in, 240V across the three phases out.
These are cheaper and you can often re configure a motor so this is ok (star
to delta). The Teco drives boost the voltage, you put 240 in and get 415
across the phases out, with a sine filter on the output you can run a
complete multiple machine shop from one inverter, and they come modified by
drives direct in very big sizes.



Mine is a 7.5Hp one which cost me £500, all other options were £850 plus. I
only run it to my 5HP spindle motor, but it is very good, and does just
about everything I could hope for.

Hope this helps

Regs Mark



Dr. Mark Vaughan Ph'D. B.Eng. M0VAU

Managing Director

Vaughan Industries Ltd, reg in UK no 2561068

Water Care Technology Ltd, reg in UK no 4129351

Addr Unit3, Sydney House, Blackwater, Truro, Cornwall, TR4 8HH, UK.
Phone/Fax 44 1872 561288

_____

From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Vince Endter
Sent: 09 February 2007 01:01
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] 5HP VFD



I am looking for a 5HP VFD that will take single phase input.
Automation directs drives stop at 3hp with single phase.

Thanks

Vince





[Non-text portions of this message have been removed]

Discussion Thread

Vince Endter 2007-02-08 17:09:22 UTC 5HP VFD John Dammeyer 2007-02-08 17:46:45 UTC RE: [CAD_CAM_EDM_DRO] 5HP VFD paultitchener 2007-02-08 17:57:29 UTC Re: 5HP VFD David A. Frantz 2007-02-08 18:41:19 UTC Re: [CAD_CAM_EDM_DRO] Re: 5HP VFD Vince Endter 2007-02-08 19:57:56 UTC Re: 5HP VFD Jon Elson 2007-02-08 20:00:07 UTC Re: [CAD_CAM_EDM_DRO] 5HP VFD turbulatordude 2007-02-09 04:56:59 UTC Re: 5HP VFD gary 2007-02-09 07:50:24 UTC Re: [CAD_CAM_EDM_DRO] 5HP VFD Ron Kline 2007-02-09 09:56:25 UTC Re: [CAD_CAM_EDM_DRO] 5HP VFD Jon Elson 2007-02-09 10:29:43 UTC Re: [CAD_CAM_EDM_DRO] 5HP VFD Jon Elson 2007-02-09 10:35:07 UTC Re: [CAD_CAM_EDM_DRO] 5HP VFD turbulatordude 2007-02-09 19:22:11 UTC Re: 5HP VFD Ron Kline 2007-02-09 20:30:48 UTC Re: [CAD_CAM_EDM_DRO] Re: 5HP VFD Jon Elson 2007-02-09 20:39:56 UTC Re: [CAD_CAM_EDM_DRO] Re: 5HP VFD Mark Vaughan 2007-02-10 09:04:27 UTC RE: [CAD_CAM_EDM_DRO] 5HP VFD robsarten 2007-02-10 23:03:35 UTC Re: 5HP VFD