Re: [CAD_CAM_EDM_DRO] 10,000 RPM spindle speed on a BP
Posted by
Wayne Weedon
on 2007-03-19 09:41:39 UTC
Polaraligned wrote:
You do have to bear in mind the speed rating of the standard bearings,
and numerous other details.
I run a VMC with a 6K rated spindle, this has a cartridge spindle
assembly with carefully preloaded bearings, it gets quite warm after a
few hours running.
Many of the spindles rated for higher rpm than mine also have chillers
to keep the temperature under control.
It's probably much safer to use a speed increaser designed for the job,
these seem to come up on ebay a fair bit.
Or even mount a small router on the quill.
Wayne....
--
---------------------------------------------------------------------------
Wayne M Weedon Email: wayne@...
Fdos Design Poole UK
Tel +44-1202-677025 Fax +44-1202-770515 Mobile: 07774 439915
Specialists in small batch & Production Mechanical/Electrical Engineering
---------------------------------------------------------------------------
>It might be !
> Is this nuts?
> Any thoughts?
You do have to bear in mind the speed rating of the standard bearings,
and numerous other details.
I run a VMC with a 6K rated spindle, this has a cartridge spindle
assembly with carefully preloaded bearings, it gets quite warm after a
few hours running.
Many of the spindles rated for higher rpm than mine also have chillers
to keep the temperature under control.
It's probably much safer to use a speed increaser designed for the job,
these seem to come up on ebay a fair bit.
Or even mount a small router on the quill.
Wayne....
--
---------------------------------------------------------------------------
Wayne M Weedon Email: wayne@...
Fdos Design Poole UK
Tel +44-1202-677025 Fax +44-1202-770515 Mobile: 07774 439915
Specialists in small batch & Production Mechanical/Electrical Engineering
---------------------------------------------------------------------------
Discussion Thread
Polaraligned
2007-03-19 04:36:04 UTC
10,000 RPM spindle speed on a BP
Wayne Weedon
2007-03-19 09:41:39 UTC
Re: [CAD_CAM_EDM_DRO] 10,000 RPM spindle speed on a BP
Doug M
2007-03-19 09:52:01 UTC
Re: [CAD_CAM_EDM_DRO] 10,000 RPM spindle speed on a BP
jerrybiehler
2007-03-19 15:06:49 UTC
Re: 10,000 RPM spindle speed on a BP
John Mesh
2007-03-19 21:31:23 UTC
Re: 10,000 RPM spindle speed on a BP
dgoadby
2007-03-20 04:26:37 UTC
Re: 10,000 RPM spindle speed on a BP
kiwiavi
2007-03-21 03:17:01 UTC
Re: 10,000 RPM spindle speed on a BP
Leslie Newell
2007-03-21 03:55:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: 10,000 RPM spindle speed on a BP
Jon Elson
2007-03-21 08:26:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: 10,000 RPM spindle speed on a BP
George Taylor, IV
2007-03-22 15:46:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: 10,000 RPM spindle speed on a BP
Leslie Newell
2007-03-22 17:10:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: 10,000 RPM spindle speed on a BP
John Mesh
2007-03-23 21:45:48 UTC
Re: 10,000 RPM spindle speed on a BP