Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Posted by
Scot Rogers
on 2007-10-20 19:37:55 UTC
I don't normally post here, but I have to chime in.
You don't really *have* to drill hard materials with diamond. You can
use a ram edm with a small electrode too. There are even plans to make
a small table top model that I built to burn stuff into hard materials.
Look up "edm book" on ebay. You should be able to find one that has
plans to build a pretty decent homebrew machine.
Jon Elson wrote:
You don't really *have* to drill hard materials with diamond. You can
use a ram edm with a small electrode too. There are even plans to make
a small table top model that I built to burn stuff into hard materials.
Look up "edm book" on ebay. You should be able to find one that has
plans to build a pretty decent homebrew machine.
Jon Elson wrote:
>
> Michael Fagan wrote:
> > Just out of curiosity, unless you're doing loads of production work,
> > wouldn't it make sense to just drill the hole, then manually thread
> the wire
> > through?
> One of the advantages to using EDM is you can cut materials that
> are incredibly hard, or have to be machined in the hard state.
> Think of cutting mounting holes in a tungsten carbide cutting
> insert. EDM does it like cutting butter. You'd need diamonds
> to drill it.
>
> Jon
>
>
> ------------------------------------------------------------------------
>
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.488 / Virus Database: 269.15.3/1081 - Release Date: 10/19/2007 5:41 PM
>
Discussion Thread
WGB
2007-10-19 21:58:32 UTC
EDM retrofit
Graham Stabler
2007-10-20 05:51:59 UTC
Re: EDM retrofit
Harko Schwartz
2007-10-20 07:02:07 UTC
Re: [CAD_CAM_EDM_DRO] EDM retrofit
Stephen Wille Padnos
2007-10-20 08:13:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Graham Stabler
2007-10-20 08:49:25 UTC
Re: EDM retrofit
Stephen Wille Padnos
2007-10-20 09:12:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Jon Elson
2007-10-20 10:36:57 UTC
Re: [CAD_CAM_EDM_DRO] EDM retrofit
Graham Stabler
2007-10-20 11:13:15 UTC
Re: EDM retrofit
Graham Stabler
2007-10-20 11:19:01 UTC
Re: EDM retrofit
Michael Fagan
2007-10-20 11:42:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Graham Stabler
2007-10-20 13:35:45 UTC
Re: EDM retrofit
Jon Elson
2007-10-20 16:00:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Graham Stabler
2007-10-20 17:50:31 UTC
Re: EDM retrofit
Scot Rogers
2007-10-20 19:37:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Jon Elson
2007-10-20 20:52:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Graham Stabler
2007-10-21 04:40:10 UTC
Re: EDM retrofit
Graham Stabler
2007-10-21 04:43:07 UTC
Re: EDM retrofit
Scot Rogers
2007-10-21 13:56:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit
Michael Fagan
2007-10-21 17:51:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM retrofit