Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Posted by
stan
on 2007-12-15 17:18:26 UTC
On Friday 14 December 2007 07:59:33 Dave Halliday wrote:
then the geometry could be corrected where the wire is turned through 90 deg
on each end, either with a floating guide or by allowing the rod to travel
along its axis. Having both the rod and guide rollers fixed and having the
guide rollers placed at the point where travel ends may allow the geometry to
equal out but I don't think it adds up.
Something kind of along the same lines as a cheap alternative to ballscrews
could be to use a short wire loop wrapped on threaded bar with 2 rollers to
loop it back around. I have no idea where to get a short loop of wire that
doesn't have a lump where the ends join though. Anyone?
cheers
BTW, is it my email or did everyone just receive this?
--
Q: What do you call the scratches that you get when a female
sheep bites you?
A: Ewe nicks.
> My concern was that as you moved the axis, the feed-point of the cableI was thinking along the same lines. If the rod was in line with the travel
> would travel up the rod so far as to introduce trigonometric distortion.
> What once was the base is now the hypotenuse and you would need a way to
> let out slack as needed.
then the geometry could be corrected where the wire is turned through 90 deg
on each end, either with a floating guide or by allowing the rod to travel
along its axis. Having both the rod and guide rollers fixed and having the
guide rollers placed at the point where travel ends may allow the geometry to
equal out but I don't think it adds up.
Something kind of along the same lines as a cheap alternative to ballscrews
could be to use a short wire loop wrapped on threaded bar with 2 rollers to
loop it back around. I have no idea where to get a short loop of wire that
doesn't have a lump where the ends join though. Anyone?
cheers
BTW, is it my email or did everyone just receive this?
--
Q: What do you call the scratches that you get when a female
sheep bites you?
A: Ewe nicks.
Discussion Thread
cnc002@a...
2007-12-12 06:58:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Kevin Martin
2007-12-12 08:31:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
stan
2007-12-12 08:41:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
cnc002@a...
2007-12-12 13:27:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Dave Halliday
2007-12-13 00:13:51 UTC
RE: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
stan
2007-12-13 02:35:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Andy Wander
2007-12-13 05:59:41 UTC
RE: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
David LeVine
2007-12-13 17:16:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
turbulatordude
2007-12-14 17:23:36 UTC
Re: I need some feedback on using wire rope for driving...
turbulatordude
2007-12-14 17:27:27 UTC
Re: I need some feedback on using wire rope for driving...
Dave Halliday
2007-12-15 16:59:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Andy Wander
2007-12-15 17:11:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Mark Bingham
2007-12-15 17:13:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
stan
2007-12-15 17:18:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
Harko Schwartz
2007-12-15 17:47:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
turbulatordude
2007-12-15 18:05:40 UTC
Re: I need some feedback on using wire rope for driving...
Callcbm
2007-12-16 05:50:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: I need some feedback on using wire rope for driving...
turbulatordude
2007-12-16 07:03:53 UTC
Re: using wire rope for driving... pix
Michael Fagan
2007-12-16 21:00:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: using wire rope for driving... pix
turbulatordude
2007-12-16 21:03:42 UTC
Re: using wire rope for driving... pix
Michael Fagan
2007-12-16 21:18:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: using wire rope for driving... pix