Re: shaft torsion ?
Posted by
carbonsteelsam
on 2008-03-19 13:40:08 UTC
Not unless they're overpowering your motors or there is an extremely
biased friction load from one rail to the other. With good setup &
alignment the rails should perform pretty much the same and the
pinions would easily handle minor side-to-side fluctuations.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Philip Burman"
<philip.burman@...> wrote:
biased friction load from one rail to the other. With good setup &
alignment the rails should perform pretty much the same and the
pinions would easily handle minor side-to-side fluctuations.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Philip Burman"
<philip.burman@...> wrote:
>loads
> Are frictional loads at constant velociy not an issue.
>
> Phil
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Kevin Martin <kpmartin@>
> wrote:
> >
> > In the original message the system was described as "5 foot wide
> gantry on a plasma cutter" so there are essentially no machining
> (unless you count the recoil from the plasma jet).carbonsteelsam
> > -Kevin Martin
> >
> > -----Original Message-----
> > From: CAD_CAM_EDM_DRO@yahoogroups.com
> [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of
> > [...]The real differential loads will result when the router isto
> the extreme end of its travel and is under heavy cutting load.[...]
> >
>
Discussion Thread
turbulatordude
2008-03-18 04:57:52 UTC
shaft torsion ?
Paul Kelly
2008-03-18 05:16:43 UTC
RE: [CAD_CAM_EDM_DRO] shaft torsion ?
Kevin Martin
2008-03-18 07:28:36 UTC
RE: [CAD_CAM_EDM_DRO] shaft torsion ?
cnc002@a...
2008-03-18 08:44:16 UTC
Re: [CAD_CAM_EDM_DRO] shaft torsion ?
turbulatordude
2008-03-18 10:52:08 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-18 15:42:13 UTC
Re: shaft torsion ?
Kevin Martin
2008-03-18 19:09:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: shaft torsion ?
carbonsteelsam
2008-03-19 08:19:37 UTC
Re: shaft torsion ?
Philip Burman
2008-03-19 10:54:38 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-19 13:40:08 UTC
Re: shaft torsion ?
Philip Burman
2008-03-21 04:20:24 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-21 08:11:24 UTC
Re: shaft torsion ?
Jon Elson
2008-03-21 09:28:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: shaft torsion ?
Philip Burman
2008-03-21 18:54:27 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-23 08:10:52 UTC
Re: shaft torsion ?
gcode fi (hanermo)
2008-03-24 08:26:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: shaft torsion ?
metlmunchr
2008-04-20 21:58:18 UTC
Re: shaft torsion ?