Re: shaft torsion ?
Posted by
Philip Burman
on 2008-03-21 04:20:24 UTC
My point was that there are "machining" loads, even at constant
velocity, that may cause "windup of the shaft. I was just interested
why this was not a problem in practice. I assumed it is due to the
relatively low level of precision required with this type of machine.
Phil
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "carbonsteelsam"
<corryharper@...> wrote:
velocity, that may cause "windup of the shaft. I was just interested
why this was not a problem in practice. I assumed it is due to the
relatively low level of precision required with this type of machine.
Phil
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "carbonsteelsam"
<corryharper@...> wrote:
>extremely
> Not unless they're overpowering your motors or there is an
> biased friction load from one rail to the other. With good setup &wide
> alignment the rails should perform pretty much the same and the
> pinions would easily handle minor side-to-side fluctuations.
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Philip Burman"
> <philip.burman@> wrote:
> >
> > Are frictional loads at constant velociy not an issue.
> >
> > Phil
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, Kevin Martin <kpmartin@>
> > wrote:
> > >
> > > In the original message the system was described as "5 foot
> > gantry on a plasma cutter" so there are essentially no machining[...]
> loads
> > (unless you count the recoil from the plasma jet).
> > > -Kevin Martin
> > >
> > > -----Original Message-----
> > > From: CAD_CAM_EDM_DRO@yahoogroups.com
> > [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of
> carbonsteelsam
> > > [...]The real differential loads will result when the router is
> to
> > the extreme end of its travel and is under heavy cutting load.
> > >
> >
>
Discussion Thread
turbulatordude
2008-03-18 04:57:52 UTC
shaft torsion ?
Paul Kelly
2008-03-18 05:16:43 UTC
RE: [CAD_CAM_EDM_DRO] shaft torsion ?
Kevin Martin
2008-03-18 07:28:36 UTC
RE: [CAD_CAM_EDM_DRO] shaft torsion ?
cnc002@a...
2008-03-18 08:44:16 UTC
Re: [CAD_CAM_EDM_DRO] shaft torsion ?
turbulatordude
2008-03-18 10:52:08 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-18 15:42:13 UTC
Re: shaft torsion ?
Kevin Martin
2008-03-18 19:09:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: shaft torsion ?
carbonsteelsam
2008-03-19 08:19:37 UTC
Re: shaft torsion ?
Philip Burman
2008-03-19 10:54:38 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-19 13:40:08 UTC
Re: shaft torsion ?
Philip Burman
2008-03-21 04:20:24 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-21 08:11:24 UTC
Re: shaft torsion ?
Jon Elson
2008-03-21 09:28:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: shaft torsion ?
Philip Burman
2008-03-21 18:54:27 UTC
Re: shaft torsion ?
carbonsteelsam
2008-03-23 08:10:52 UTC
Re: shaft torsion ?
gcode fi (hanermo)
2008-03-24 08:26:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: shaft torsion ?
metlmunchr
2008-04-20 21:58:18 UTC
Re: shaft torsion ?