Re: [CAD_CAM_EDM_DRO] "Homemade moglice", ideas?!
Posted by
gary
on 2008-03-29 21:10:09 UTC
Suggest that you consider painting the screw with a coat of enamel
before casting the nut. Coat the outside of the painted screw with the
mold release and after removing the cast nut clean off the paint. This
should give enought clearance for the nut to operate.
gary
Mike Pogue wrote:
before casting the nut. Coat the outside of the painted screw with the
mold release and after removing the cast nut clean off the paint. This
should give enought clearance for the nut to operate.
gary
Mike Pogue wrote:
> I cast some bearings around some socket head shoulder screws this way...[Non-text portions of this message have been removed]
> They seemed to work OK, although it was a bit messy. The bearings ended
> up being quite tight.
>
> I used West Systems Epoxy (105/205) with 423 graphite powder,
> and a MS122AD PTFE release agent. I tried several ratios
> of graphite, and they all seemed to work pretty much the same.
>
> I thought about also casting a zero backlash feednut, but I figured
> that the natural small tolerances in the threads (I'm not using
> a precision leadscrew) would result in too much binding.
>
> HTH,
> Mike
>
> Jon Elson wrote:
> > efraimbarkbit wrote:
> >
> >>What about making a batch out of: quality epoxy resin, graphite powder
> >>and atomized (at least very fine!)PTFE? Any ideas on proportions etc.?
> >>I can get all of the above within reasonable financial limits, and
> >>could do a trial run of let's say 10 batches for making zerobacklash
> >>feednuts. It should be possible to make something similar to
> >>Mogliceputty (or injectable Moglice)
> >
> > Graphite can be quite abrasive, depends on how it is made.
> > Moglice has Molybdenum diSulfide, not graphite, as the
> > lubricating element.
> >
> > Jon
> >
>
>
Discussion Thread
efraimbarkbit
2008-03-29 16:43:03 UTC
"Homemade moglice", ideas?!
Jon Elson
2008-03-29 16:57:31 UTC
Re: [CAD_CAM_EDM_DRO] "Homemade moglice", ideas?!
Mike Pogue
2008-03-29 18:15:23 UTC
Re: [CAD_CAM_EDM_DRO] "Homemade moglice", ideas?!
gary
2008-03-29 21:10:09 UTC
Re: [CAD_CAM_EDM_DRO] "Homemade moglice", ideas?!
Ron Ginger
2008-03-31 08:04:31 UTC
Re: "Homemade moglice", ideas?!
turbulatordude
2008-03-31 15:10:53 UTC
Re: "Homemade moglice", ideas?!
ken
2008-04-01 21:09:56 UTC
Re: "Homemade moglice", ideas?!
notoneleft
2008-04-02 14:43:03 UTC
Re: "Homemade moglice", ideas?!
efraimbarkbit
2008-04-03 11:37:31 UTC
Re: "Homemade moglice", ideas?!
Mark Bingham
2008-04-03 13:18:41 UTC
Re: "Homemade moglice", ideas?!
H & J Johnson
2008-04-03 13:18:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: "Homemade moglice", ideas?!
turbulatordude
2008-04-04 07:04:27 UTC
Re: "Homemade moglice", ideas?!
Maxi Bertotto
2008-04-04 18:41:06 UTC
Some tecnical questions...
Yahoo
2008-04-05 08:51:57 UTC
Re: Some tecnical questions...