Re: [CAD_CAM_EDM_DRO] Ref: Ballscrew machining
Posted by
gary burke
on 2008-04-12 09:04:19 UTC
I drilled or bored a round alumn to the size of the ballscrew, them cut a slot though the full length, then when i tighten the jaws it clamps down on the ballscrew, and doesn't mark it up or scratch it...
Gary
----- Original Message ----
From: stan <stan.distortion@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Saturday, April 12, 2008 11:44:10 AM
Subject: [CAD_CAM_EDM_DRO] Ref: Ballscrew machining
A bit of care and there will be no problems. Rolled screws are softer so
softjaws, a jig or aluminium strips between the jaws and the screw would be a
needed. Ground screws are more or less the same hardness as bearings and
should be fine clamped directly but softjaws would be a good idea.
If the machining isn't a stupid price it may be a good idea to make use of the
service, if they screw up they replace them.
Steel this hard is a bit of a pig to machine, try a few old roller bearings
first if you have never done anything with it. A bit of practice and you
shouldn't need to grind, the turned finish should be accurate with good,
sharp tungsten tooling.
Have a think how you are going to center it, 0.02mm is to much runout and will
bind at the end of the travel with good quality bearings and rigid slides.
The nut should be concentric but turn it and re-test after centering just in
case.
cheers
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
[Non-text portions of this message have been removed]
Gary
----- Original Message ----
From: stan <stan.distortion@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com
Sent: Saturday, April 12, 2008 11:44:10 AM
Subject: [CAD_CAM_EDM_DRO] Ref: Ballscrew machining
A bit of care and there will be no problems. Rolled screws are softer so
softjaws, a jig or aluminium strips between the jaws and the screw would be a
needed. Ground screws are more or less the same hardness as bearings and
should be fine clamped directly but softjaws would be a good idea.
If the machining isn't a stupid price it may be a good idea to make use of the
service, if they screw up they replace them.
Steel this hard is a bit of a pig to machine, try a few old roller bearings
first if you have never done anything with it. A bit of practice and you
shouldn't need to grind, the turned finish should be accurate with good,
sharp tungsten tooling.
Have a think how you are going to center it, 0.02mm is to much runout and will
bind at the end of the travel with good quality bearings and rigid slides.
The nut should be concentric but turn it and re-test after centering just in
case.
cheers
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
[Non-text portions of this message have been removed]
Discussion Thread
john_glynn57
2008-04-12 08:24:01 UTC
Ballscrew machining
stan
2008-04-12 08:44:21 UTC
Ref: Ballscrew machining
Torsten
2008-04-12 08:50:19 UTC
Re: Ballscrew machining
stan
2008-04-12 08:55:35 UTC
Ref: Ballscrew machining
gary burke
2008-04-12 09:04:19 UTC
Re: [CAD_CAM_EDM_DRO] Ref: Ballscrew machining
JanRwl@A...
2008-04-12 09:23:24 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew machining
Jon Elson
2008-04-12 11:34:20 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew machining
R Rogers
2008-04-12 13:47:21 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew machining
Dan Mauch
2008-04-12 15:22:46 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew machining
Steve Blackmore
2008-04-12 16:47:12 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew machining
NEVILLE WEBSTER
2008-04-12 16:51:40 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrew machining
carbonsteelsam
2008-04-13 08:37:48 UTC
Re: Ballscrew machining
john_glynn57
2008-04-13 14:06:26 UTC
Re: Ballscrew machining
Steve Blackmore
2008-04-13 16:57:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrew machining
john_glynn57
2008-04-14 07:49:13 UTC
Re: Ballscrew machining