CAD CAM EDM DRO - Yahoo Group Archive

Re: Synchronizing Two Servo Motors

Posted by Yahoo
on 2009-03-13 15:38:20 UTC
Thanks, but I've already built the leadscrew assemblies.
--
Phil Mattison

----- Original Message -----
From: Roland Jollivet <Roland.Jollivet@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, March 12, 2009 12:10 AM
Subject: Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors


> I think you misunderstood my proposal.
>
> Use the belt as the drive mechanisn, not an axis coupling device.
>
> So you have a belt on either side of the gantry, running along the rail.
> Maybe the belt is 6m per side, looped and joined at the carrige.
>
> Then at one end of the machine, you have a shaft, as wide as the rails,
with
> a pulley at each end. The motor is directly coupled to the shaft.
>
> And the belts are perfectly suited to this application.
>
> Regards
> Roland
>
> 2009/3/11 Yahoo <yahoo@...>
>
> > Unfortunately those are open-ended belts. I need continuous loop,
which
> > tops
> > out at 48", then jumps to 120" with nothing in between.
> > --
> > Phil Mattison
> >
>

Discussion Thread

Mattison 2009-03-10 12:02:18 UTC Synchronizing Two Servo Motors Alan Marconett 2009-03-10 12:14:47 UTC RE: [CAD_CAM_EDM_DRO] Synchronizing Two Servo Motors Roland Jollivet 2009-03-10 13:10:41 UTC Re: [CAD_CAM_EDM_DRO] Synchronizing Two Servo Motors Yahoo 2009-03-10 13:29:04 UTC Re: Synchronizing Two Servo Motors H & J Johnson 2009-03-10 13:39:52 UTC Re: [CAD_CAM_EDM_DRO] Synchronizing Two Servo Motors Stephen Wille Padnos 2009-03-10 14:08:18 UTC Re: [CAD_CAM_EDM_DRO] Synchronizing Two Servo Motors H & J Johnson 2009-03-10 14:27:34 UTC Re: [CAD_CAM_EDM_DRO] Synchronizing Two Servo Motors Stephen Wille Padnos 2009-03-10 14:59:00 UTC Re: [CAD_CAM_EDM_DRO] Synchronizing Two Servo Motors Yahoo 2009-03-10 17:14:37 UTC Re: Synchronizing Two Servo Motors Jon Elson 2009-03-10 19:50:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors jcc3inc 2009-03-11 05:48:59 UTC Re: Synchronizing Two Servo Motors Yahoo 2009-03-11 10:06:29 UTC Re: Synchronizing Two Servo Motors Franklin York 2009-03-11 12:00:51 UTC RE: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors Roland Jollivet 2009-03-11 12:02:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors Yahoo 2009-03-11 14:03:18 UTC Re: Synchronizing Two Servo Motors Torsten 2009-03-11 16:58:45 UTC Re: Synchronizing Two Servo Motors Jon Elson 2009-03-11 19:32:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors Roland Jollivet 2009-03-11 22:05:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors Roland Jollivet 2009-03-13 15:09:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors Yahoo 2009-03-13 15:38:20 UTC Re: Synchronizing Two Servo Motors Brian Pitt 2009-03-14 10:30:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Synchronizing Two Servo Motors