Posts by jcc3inc

jcc3inc 2002-02-09 13:37:40 UTC Re: Flame cutting tables jcc3inc 2002-02-21 09:16:40 UTC Re: Keyboard Questions jcc3inc 2002-02-21 09:23:31 UTC Re: arc or curve fitting program jcc3inc 2002-03-26 06:24:52 UTC Re: Encoder to Step/Dir converter MPG jcc3inc 2002-03-28 06:32:17 UTC Re: Newbie Loosing Mind........Need Shootout......Small Desktops..FAST jcc3inc 2002-05-05 15:02:12 UTC Setup Help jcc3inc 2002-05-15 06:52:07 UTC Re: BP Conversion ??? jcc3inc 2002-05-30 07:57:26 UTC Look-ahead jcc3inc 2002-07-09 07:30:13 UTC Re: Engraving on Mill jcc3inc 2002-07-09 07:41:19 UTC Re: SYNCRONIZATION jcc3inc 2002-09-29 06:59:36 UTC Re: engraving with excel jcc3inc 2002-09-30 07:15:46 UTC Re: Rack and pinion jcc3inc 2002-10-25 07:08:05 UTC Re: RACK AND SPUR GEAR FORMULATION jcc3inc 2002-10-29 06:44:30 UTC Re: DRO encoders- Rotary or Linear? jcc3inc 2002-12-03 13:56:27 UTC Re: Convert Step/Dir to +/-10v jcc3inc 2002-12-06 06:24:26 UTC Re: Convert G-Code inch to millimeters jcc3inc 2003-04-21 17:29:03 UTC Cutter Compensation Program jcc3inc 2003-05-08 06:52:22 UTC Re: Can my CNC controller blow my motherboard? jcc3inc 2003-05-12 07:15:00 UTC Re: Rotary table DRO jcc3inc 2003-06-28 07:37:08 UTC Re: analog to pwm jcc3inc 2003-06-28 07:47:58 UTC Re: oscilloscope for CNC jcc3inc 2003-08-13 04:43:45 UTC Re: Why not lineal feedback, instead of rotary encoders? jcc3inc 2003-09-28 06:37:25 UTC Re: What kind of belt for router table? jcc3inc 2003-09-28 06:42:28 UTC Re: Servo Operating Temperature? jcc3inc 2003-10-13 06:51:40 UTC Re: Step/dir control for DC motor jcc3inc 2003-11-04 05:53:04 UTC Re: 3D Text Carving jcc3inc 2003-11-18 17:55:34 UTC Computer Choice jcc3inc 2003-12-02 07:05:29 UTC Re: Rack and pinion jcc3inc 2003-12-14 08:10:16 UTC Manual Pulse Generator Question jcc3inc 2003-12-14 08:14:34 UTC MPG Source? jcc3inc 2004-01-11 06:55:28 UTC Re: Trak cnc 2 control replacement jcc3inc 2004-01-29 06:46:25 UTC Re: Inexpensive ACME (lead) screws jcc3inc 2004-02-27 07:40:29 UTC Tool Comp G41/G42 Program question jcc3inc 2004-02-27 07:59:32 UTC Re: Tool Comp G41/G42 Program question jcc3inc 2004-04-30 06:12:53 UTC Re: What about a Stepper with Encoder? jcc3inc 2004-06-30 05:50:31 UTC Re: Rack and pinion how to figure torque and pitch angle why 14 deg jcc3inc 2004-09-27 06:34:04 UTC Re: rotary encoder versus glass scales jcc3inc 2004-11-08 06:20:25 UTC Re: cut an elipse jcc3inc 2004-12-07 18:20:51 UTC CAD Questions jcc3inc 2004-12-09 06:21:36 UTC Re: CAD Questions jcc3inc 2005-01-08 05:52:53 UTC Re: Cheapest Bridgeport Ballscrew sets? jcc3inc 2005-10-28 11:20:54 UTC Re: the L6203 & L297 circuit heats up stepper when not clocking? jcc3inc 2006-02-12 07:16:15 UTC Re: Problem keeping my gantry square, using a dual drive slaved set-up with Gecko’s. jcc3inc 2006-08-29 08:18:32 UTC Re: Bridgeport for CNC, what to look for? jcc3inc 2006-09-21 15:19:22 UTC Re: Bridgeport series 1 retrofit? jcc3inc 2006-09-26 19:42:57 UTC Re: Video of my resonance jcc3inc 2006-11-09 07:06:17 UTC Re: 20 degree gear racks jcc3inc 2006-11-26 07:10:22 UTC Re: I started to build my CNC router Yesterday jcc3inc 2007-01-24 18:35:59 UTC Re: Looking for plans for small plasma cutting table jcc3inc 2007-12-23 07:24:31 UTC Re: Noob question - shaft couplers jcc3inc 2008-02-10 08:56:27 UTC Re: CNC acetylene torch table drive jcc3inc 2008-02-28 09:34:31 UTC Re: PC to controller comunication protocols jcc3inc 2008-02-28 10:09:42 UTC Picture posting jcc3inc 2008-03-17 13:17:19 UTC Recurrent missing pulses jcc3inc 2009-03-11 05:48:59 UTC Re: Synchronizing Two Servo Motors jcc3inc 2009-06-29 05:28:57 UTC wetRe: [CAD_CAM_EDM_DRO] Looking for CNC Plasma jcc3inc 2012-04-20 07:01:06 UTC Re: are 3/4 shafts good for axis ? jcc3inc 2013-06-18 07:07:03 UTC Re: Long Acme threaded rod