RE: [CAD_CAM_EDM_DRO] Re: Remember Mr. Bill's servo lite?

...or it happens when you connect it to equipment, such as Gecko drives.

Andy Wander

-----Original Message-----
From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Jeffrey T. Birt
Sent: Saturday, January 14, 2012 11:28 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: RE: [CAD_CAM_EDM_DRO] Re: Remember Mr. Bill's servo lite?

Conductors (wires) are not perfect; there is always a small amount of
resistance. When current flows through a wire there will be a voltage drop
across this resistance, add in the myriad of connections as wires make their
way from outlet to outlet in your house and visualize all these different
voltage drops across the various bits of wire and you can start to see that
neutral will never be at ground potential (but it should be close). This is
why we bother with the third 'ground' conductor, since it is not used to
carry current it should always be very close to ground potential and provide
a low impedance path to ground.



All DC power supplies are not tied to ground. How and why they might be can
get complex. Grounding of the negative side of a DC supply is typically done
to provide to provide a low impedance path to earth (for noise immunity).



Jeff



From: CAD_CAM_EDM_DRO@yahoogroups.com
[mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Andy Wander
Sent: Saturday, January 14, 2012 9:29 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: RE: [CAD_CAM_EDM_DRO] Re: Remember Mr. Bill's servo lite?





Now I'm intrigued. Since the neutral line is attached to same exact ground
bus bar in most electrical panels, what could make it "not" stay at or near
ground potential?

I agree on the potential for problems if you use a bridge rectifier, but
again, if you are going to be grounding one side of the DC supply anyway,
then what is it that causes the danger?

Andy Wander






[Non-text portions of this message have been removed]



------------------------------------

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner

Yahoo! Groups Links