[CAD_CAM_EDM_DRO] Long Acme threaded rod
Posted by
Roland Jollivet
on 2013-06-17 08:57:30 UTC
Drive the nut and not the rod. Keep the rod fixed in tension.
The same can apply to a belt. Drive the cog and not the belt. So the belt
will lay flat except for a hump where it is guided over the pulley. Since
the belt is now half as long, you can double up on the width for the same
price, for extra stiffness.
Regards
Roland
The same can apply to a belt. Drive the cog and not the belt. So the belt
will lay flat except for a hump where it is guided over the pulley. Since
the belt is now half as long, you can double up on the width for the same
price, for extra stiffness.
Regards
Roland
On 17 June 2013 17:25, Steve Greenfield <alienrelics@...> wrote:
> **
>
>
> Try not to laugh...
>
> I'm working on designing and building a CNC mill/engraver. I'd like it to
> have a cut volume of approximately 1000x1500x100mm (about 3ft by 5ft by 4
> inches) that can cut aluminum plate and hardwood, at most. I expect to take
> multiple passes to cut through an aluminum plate.
>
> I'm basing the design on the ShapeOko machine sized up, using 8020 in the
> 25mm size with Openrail hardcoat and grooved steel ball or delrin bearings
> rather than ground rods and linear bearings. The Y travel will have two
> steppers driving it.
>
> Something like this, except the Y rails will be fully supported by another
> piece of 8020 extrusion bolted alongside and the 8020 along the front and
> back will be raised so I can slide a longer sheet in:
> http://powercordlabs.com/1200mm-x-1200mm-shapeoko-build/
>
> Openrail:
> http://openbuildspartstore.com/openrail-hard-coat/
>
> The ShapeOko uses timing belts to move things, but for the size I want, I
> am worried about stretching. So I'm planning on using Acme rod. However,
> I'm worried about a 1500mm long Acme rod whipping. I already have some 6ft
> 1/2-10 and there are anti-backlash Delrin nuts available, but that seems
> thin for such a long rod.
>
> I have considered ballscrews, but the price is fairly high and it is
> cheaper to get a more powerful stepper to make up the power loss. Although
> if there will be a significant performance difference, I'll save a bit
> longer. I am not trying for 0.5 thou cut accuracy. I'll be cutting aluminum
> panels for equipment builds (slots for slide pots, holes for controls and
> buttons, holes for displays), and engraving/2-1/2D machining of plywood,
> hardwoods, machineable wax, plastics, etc. Probably the parts requiring the
> most accuracy will be wooden gears for clocks, driven by a stepper motor.
>
> Am I completely off track? There are also steel wire reinforced timing
> belts available.
>
> Steve Greenfield AE7HD
> http://www.linkedin.com/in/stevenjgreenfield
>
> [Non-text portions of this message have been removed]
>
>
>
[Non-text portions of this message have been removed]
Discussion Thread
Steve Greenfield
2013-06-17 08:25:59 UTC
Long Acme threaded rod
Andy Wander
2013-06-17 08:38:11 UTC
RE: [CAD_CAM_EDM_DRO] Long Acme threaded rod
cnc sales (hanermo)
2013-06-17 08:44:50 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Jamie Cunningham
2013-06-17 08:45:12 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Roland Jollivet
2013-06-17 08:57:30 UTC
[CAD_CAM_EDM_DRO] Long Acme threaded rod
Art Eckstein
2013-06-17 09:01:34 UTC
RE: [CAD_CAM_EDM_DRO] Long Acme threaded rod
cnc sales (hanermo)
2013-06-17 09:17:40 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Tony Smith
2013-06-17 10:18:14 UTC
RE: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Tony Smith
2013-06-17 10:39:42 UTC
RE: [CAD_CAM_EDM_DRO] Long Acme threaded rod
AlienRelics
2013-06-17 12:10:37 UTC
Re: Long Acme threaded rod
Jamie Cunningham
2013-06-17 12:14:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Long Acme threaded rod
Roland Jollivet
2013-06-17 12:31:09 UTC
[CAD_CAM_EDM_DRO] Re: Long Acme threaded rod
Drew Rogge
2013-06-17 13:17:56 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Steve Blackmore
2013-06-17 14:21:36 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Ron Thompson
2013-06-17 15:41:38 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
AlienRelics
2013-06-17 18:39:04 UTC
Re: Long Acme threaded rod
jcc3inc
2013-06-18 07:07:03 UTC
Re: Long Acme threaded rod
David G. LeVine
2013-06-21 19:38:57 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod
Steve Blackmore
2013-06-21 23:53:58 UTC
Re: [CAD_CAM_EDM_DRO] Long Acme threaded rod