Posts by tig415
tig415
2002-01-13 05:52:28 UTC
Gecko 340 reset manager (for Marris)
tig415
2002-02-11 16:20:07 UTC
Looking for a router alternative.
tig415
2002-03-22 03:23:52 UTC
Servo motors with Geckos get hot when idle.
tig415
2002-03-22 07:35:45 UTC
Re: Servo motors with Geckos get hot when idle.
tig415
2002-03-22 11:27:31 UTC
Re: Servo motors with Geckos get hot when idle.
tig415
2002-08-28 12:41:02 UTC
Loosing steps with Gecko 340 drive
tig415
2002-09-03 09:21:20 UTC
Loosing steps with Gecko 340 drive--Mariss?
tig415
2002-09-04 04:25:00 UTC
Re: Loosing steps with Gecko 340 drive--Mariss?
tig415
2002-09-04 04:26:09 UTC
Re: Loosing steps with Gecko 340 drive--Mariss?
tig415
2002-09-23 03:19:58 UTC
Re: solid works
tig415
2002-09-23 14:46:58 UTC
Re: cutting stainless steel sheet
tig415
2002-11-17 14:23:26 UTC
extending linear rail by butting two pieces together
tig415
2002-11-18 04:03:27 UTC
Re: FREE CAM ????!!!!!!! (disappointment, really)
tig415
2002-11-29 15:55:46 UTC
Question about Marisss err/reset board
tig415
2003-03-15 09:38:55 UTC
Anilam glass scale hookup question
tig415
2003-03-15 17:59:39 UTC
Re: Anilam glass scale hookup question
tig415
2003-03-16 04:35:12 UTC
More Anilam questions for droguy.
tig415
2003-03-17 08:36:38 UTC
More westamp info on anilam control
tig415
2003-03-22 09:48:18 UTC
More Anilam glass scale hookup questions for dro guy
tig415
2003-03-22 09:58:35 UTC
Re: More Anilam glass scale hookup questions oops!!!!!
tig415
2003-04-09 09:58:42 UTC
Spindle question
tig415
2003-04-10 14:37:46 UTC
Spindle question again . First post was as clear as mud
tig415
2003-04-19 03:24:37 UTC
Glass scale problem
tig415
2003-04-20 16:57:34 UTC
Subject: Re: Glass scale problem
tig415
2003-05-30 03:43:28 UTC
Whats a good speed for a rotary table?
tig415
2003-05-30 10:56:03 UTC
Re: What's a good speed for a rotary table?..More info
tig415
2003-06-21 03:37:55 UTC
Re: convert drawing to cad file
tig415
2003-08-03 07:29:32 UTC
Need opinions on Gecko wiring.
tig415
2003-08-12 08:08:48 UTC
Using ribbon cable for parallel port
tig415
2003-08-19 18:08:25 UTC
Rutex drive opinions needed
tig415
2003-08-22 07:40:04 UTC
Gecko 340 drives and tuning
tig415
2003-08-27 04:50:43 UTC
Enco knee mill on Ebay
tig415
2003-10-10 19:14:49 UTC
Re: Router bearing failure
tig415
2003-12-09 06:28:54 UTC
Best way to estop a servo drive.
tig415
2004-02-12 09:59:36 UTC
Re: Question about VM 4 and Mach2
tig415
2004-02-23 09:47:43 UTC
Rutex 0-10v to servo drive question
tig415
2004-02-25 02:45:28 UTC
Re: DRO meaning in the Artofcnc world
tig415
2004-02-27 08:21:10 UTC
Rutex Z axis problem--more info
tig415
2004-02-27 12:25:37 UTC
Re: Rutex Z axis problem--more info
tig415
2004-02-28 05:22:14 UTC
Rutex Z axis problem solved
tig415
2004-05-01 10:14:23 UTC
Problem with a Gecko 340
tig415
2004-05-01 16:59:54 UTC
Re: Problem with a Gecko 340
tig415
2004-05-04 05:41:40 UTC
Running two motors from one vfd
tig415
2004-08-03 04:59:55 UTC
Air cooling Bosch router bearing