Re: Digital Caliper Output
Posted by
Lee Studley
on 2000-10-10 13:00:11 UTC
Hi,
CircuitCellar.com had an article years ago on getting the serial
output(usually implemented but not always brought out to a connecter)
on these digital calipers. there's usually pads to get to the
data output if I remember clearly. The format needs to be reformatted
I think...
I'll search their site to try to get the article, or pdf a copy of
the
issue in my storage. Might take a couple of days till I get to it.
-Lee
CircuitCellar.com had an article years ago on getting the serial
output(usually implemented but not always brought out to a connecter)
on these digital calipers. there's usually pads to get to the
data output if I remember clearly. The format needs to be reformatted
I think...
I'll search their site to try to get the article, or pdf a copy of
the
issue in my storage. Might take a couple of days till I get to it.
-Lee
--- In CAD_CAM_EDM_DRO@egroups.com, Jon Elson <jmelson@a...> wrote:
>
>
> bcollier@p... wrote:
>
> > I wonder if the half-thou digit toggles between 0 and 5 in real
time.
> > You could tap into the LCD and read, say, the lower left line in
the
> > tenth place. If it is real time, you would get a square wave
pulse,
> > high every half-thou. Any thoughts?
>
> They don't work that way. About 500 times a second, the chip
selects
> one digit
> at a time and sends the 7 segment drive signals to it. Then, it
does
> the next
> digit. Even if what you suggest was how it worked, you would have
lost
> direction of travel information.
>
> Yes, you could pick up all the digits and de-multiplex them, and get
> faster readout
> than the spc port, but I'm not sure it is fast enough, still. But,
> you'd get about
> 60-100 full updates/second.
>
> Jon
Discussion Thread
bcollier@p...
2000-10-09 10:18:15 UTC
Digital Caliper Output
Jon Elson
2000-10-09 22:55:37 UTC
Re: [CAD_CAM_EDM_DRO] Digital Caliper Output
Doug Fortune
2000-10-09 23:42:18 UTC
Re: [CAD_CAM_EDM_DRO] Digital Caliper Output
bcollier@p...
2000-10-10 07:19:09 UTC
Re: Digital Caliper Output
Anne Ogborn
2000-10-10 10:33:37 UTC
Re: [CAD_CAM_EDM_DRO] Digital Caliper Output
Mark Fraser
2000-10-10 12:05:03 UTC
Digital Caliper Output
Jon Elson
2000-10-10 12:30:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digital Caliper Output
Lee Studley
2000-10-10 13:00:11 UTC
Re: Digital Caliper Output
Lee Studley
2000-10-10 13:00:34 UTC
Re: Digital Caliper Output
ballendo@y...
2000-10-10 15:29:25 UTC
Re: Digital Caliper Output
bcollier@p...
2000-10-11 07:19:22 UTC
Re: Digital Caliper Output
bcollier@p...
2000-10-11 07:26:12 UTC
Re: Digital Caliper Output
Anne Ogborn
2000-10-11 14:36:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digital Caliper Output
Lee Studley
2000-10-11 15:56:21 UTC
Re: Digital Caliper Output
Alison & Jim Gregg
2000-10-11 19:13:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digital Caliper Output
Anne Ogborn
2000-10-11 22:46:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digital Caliper Output
Alison & Jim Gregg
2000-10-11 23:21:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digital Caliper Output
dave engvall
2000-10-14 17:19:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digital Caliper Output