CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Lathe Software question

on 2000-10-12 06:42:51 UTC
Jim: You are kidding ,right? We are talking about tens of thousands of
extra pulses in under a second here.The axis went to rapid feed. It just
went screaming off into the part.
Carey

Alison & Jim Gregg wrote:

> Hi Carey
>
> Sounds like random (electrical) noise getting into the system somehow.
>
> Perhaps checking the grounding / bonding between the laptop and the
> system
> might be a way to go.
>
> Jim Gregg
>
> At 09:05 PM 10/11/00 -0400, you wrote:
> >Ballendo: Yep, it was the z axis and it was a rapid move. Zip-crunch-
>
> >dive for the escape key. Lots of pulses came from somewhere at the
> wrong
> >time. Several times I encountered something else that was strange.
> While
> >setting my coordinates after a tool change, I would set one axis and
> jog
> >to a different point to set the other axis only to find that the one
> >already set was making big numbers like a half inch move showing ten
> >inches or something like that. I checked the settings file and came
> back
> >and it was normal. I again figured it was the notebook computer doing
>
> >strange things. It has not done that for a while.Hmmmm.
> >Carey
> >Addresses:
> >Post message: CAD_CAM_EDM_DRO@egroups.com
> >Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> >Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> >List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> >Moderator: jmelson@... [Moderator]
> >URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> >FAQ: http://www.ktmarketing.com/faq.html
> >bill,
> >List Manager
> >
>
>
> eGroups Sponsor

>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager


[Non-text portions of this message have been removed]

Discussion Thread

wanliker@a... 2000-10-10 22:24:44 UTC Re: [CAD_CAM_EDM_DRO] Lathe Software question Carey L. Culpepper 2000-10-11 06:14:03 UTC Re: [CAD_CAM_EDM_DRO] Lathe Software question ballendo@y... 2000-10-11 17:47:33 UTC Re: Lathe Software question Carey L. Culpepper 2000-10-11 18:08:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Lathe Software question Alison & Jim Gregg 2000-10-11 19:42:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Lathe Software question Carey L. Culpepper 2000-10-12 06:42:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Lathe Software question Alison & Jim Gregg 2000-10-12 16:52:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Lathe Software question