CAD CAM EDM DRO - Yahoo Group Archive

Re: A bit off topic - resistance welding

on 2000-10-17 08:37:32 UTC
Also check out Home Shop Machinist, issue March/April 1996 page 48 for
an article on a small shop butt welder. This might be able to be used
as a spot welder with some minor changes.

John Guentther

--- In CAD_CAM_EDM_DRO@egroups.com, "Robert Grauman" <rgrauman@c...>
wrote:
> The MEW issues with the bandsaw welder/spot welder article are #41
and #42.
>
> Robert Grauman in Sunny Alberta
>
> > Hello Ian,
> >
> > Model Engineers Workshop magazine described a combination bandsaw
blade
> > welder/spot welder that would appear to meet your requirements.
> > Unfortunately, I have just loaned out a stack of my MEW magazines,
and all
> I
> > can tell you is the device was described in two consecutive issues
> somewhere
> > between issue 26 and issue 56. Give me a couple of days, and I
can get
> the
> > correct issue numbers for you, if you are interested. The welder
used a
> low
> > voltage secondary as described in other postings, with a timing
device to
> > control the weld period.
> >
> > Robert Grauman in Sunny Alberta
> >
> > > Hi,
> > >
> > > I know this is a bit off topic but I know you lot out there have
all the
> > > expertise in the world!
> > >
> > > Does anyone have any idea whether it would be possible to make a
simple
> > > resistance welding set-up for tiny jobs? Basically what I am
wanting is
> a
> > > way of spot welding bits of watch or small clock mainspring
material
> > > together - spring steel up to about 15 thou thick with welds
probably
> > about
> > > 1.64" diameter. I was thinking it might be possible using just a
big
> power
> > > supply and capacitor like in EDM and discharge this through some
kind of
> > > 'clip' but I'm not sure how to control the discharge (SCR,
Triac?) Also
> > I'm
> > > not sure about the voltage/current needed - a 24 volt, 10 Amp
> transformer
> > > with a bridge rectifier and 10,000uf capacitor seems to give an
> impressive
> > > spark but would this be enough to weld my bits of steel or is it
only
> good
> > > at screwdriver blades? ;o)
> > >
> > > Any comments would be appreciated.
> > >
> > > Ian
> > > --
> > > Ian W. Wright
> > > Sheffield UK
> >
> >

Discussion Thread

Ian Wright 2000-10-16 04:28:27 UTC A bit off topic - resistance welding Bertho Boman 2000-10-16 04:52:06 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Rich D. 2000-10-16 08:03:25 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Lee Studley 2000-10-16 10:43:16 UTC Re: A bit off topic - resistance welding Anne Ogborn 2000-10-16 10:58:29 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Alan Marconett KM6VV 2000-10-16 11:08:15 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Bertho Boman 2000-10-16 12:26:16 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Paul Corner 2000-10-16 12:46:14 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Ron Ginger 2000-10-16 12:55:46 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding wanliker@a... 2000-10-16 13:01:59 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Ian Wright 2000-10-16 13:32:45 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Tim Goldstein 2000-10-16 13:43:38 UTC RE: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding ballendo@y... 2000-10-16 15:45:13 UTC Re: A bit off topic - resistance welding Hugh Mahlendorf 2000-10-16 19:34:41 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Doug Warner 2000-10-16 20:56:42 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Robert Grauman 2000-10-16 21:06:01 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding wanliker@a... 2000-10-16 21:14:09 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Matt Shaver 2000-10-16 21:17:40 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Jon Elson 2000-10-16 22:09:33 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Randy Gordon-Gilmore 2000-10-16 22:44:04 UTC Re: A bit off topic - resistance welding Ian Wright 2000-10-17 02:18:06 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding Robert Grauman 2000-10-17 08:26:58 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding John D. Guenther 2000-10-17 08:37:32 UTC Re: A bit off topic - resistance welding Darrell 2000-10-17 09:47:48 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding wanliker@a... 2000-10-17 11:23:52 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding James Owens 2000-10-17 11:51:06 UTC Re: [CAD_CAM_EDM_DRO] A bit off topic - resistance welding