CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Free Software

Posted by Ian Wright
on 2000-10-30 02:38:20 UTC
HI,

Can you elabotate on the 'corner cutting end mills' please? As far as I was
aware, any endmill has to produce rounded inside corners simply because of
its own mass - is there something I don't know?

Also, I believe that the 'end cutting endmills' you are referring to are
generally known as 'slot drills'

Ian
--
Ian W. Wright
Sheffield UK
----- Original Message -----
From: "Smoke" <Smoke@...>
To: <CAD_CAM_EDM_DRO@egroups.com>
Sent: 30 October 2000 01:30
Subject: Re: [CAD_CAM_EDM_DRO] Re: Free Software


> Look at the bottom of the end mill...the cutting flutes across the face
will go all the way to the ceter of the mill. When you order the end mills,
the catalog will specify if they are center cutting.
>
> If you replace a standard straight (cuts square corners) cutting end mill
with one having corner cutting radii, you won't need to make any software
changes. Just be aware tho' that ALL the inside corners would then have a
corner fillet after cutting.
>
> Smoke
>
>
> I never drill a pilot hole. My draft operations are usually with center
cutting end mill
> (I guess), as they're either with a ball end mill or with a big 1/8" (OK,
for me that's
> HUGE) end mill. I don't know how to tell if this thing is center cutting
or not.
> How do I tell?
>
> eGroups Sponsor
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>
>
> [Non-text portions of this message have been removed]
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
>
>

Discussion Thread

Joe Vicars 2000-10-26 08:57:46 UTC Free Software Fred Smith 2000-10-26 19:05:30 UTC Re: Free Software Smoke 2000-10-26 19:16:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Anne Ogborn 2000-10-26 20:37:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-26 21:37:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-26 21:38:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Anne Ogborn 2000-10-27 21:10:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-27 22:01:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Tim Goldstein 2000-10-27 22:09:24 UTC RE: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-27 22:14:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Anne Ogborn 2000-10-27 22:26:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Jon Elson 2000-10-27 23:41:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software ptengin@a... 2000-10-28 02:42:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software ptengin@a... 2000-10-28 02:45:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-28 10:15:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Anne Ogborn 2000-10-29 00:33:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-29 07:03:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Anne Ogborn 2000-10-29 10:00:56 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-29 18:07:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Ian Wright 2000-10-30 02:38:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software Smoke 2000-10-30 08:07:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Free Software