Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
Posted by
wanliker@a...
on 2000-11-10 18:53:55 UTC
In a message dated 11/10/00 1:24:52 PM Mountain Standard Time,
Smoke@... writes:
<<
If your going to cut timing belt pulleys, I'd recomend using a hob and
cutting them as you would a gear. The edges of the grooves need to be
rounded over to prevent cutting the blets.
Smoke@... writes:
<<
If your going to cut timing belt pulleys, I'd recomend using a hob and
cutting them as you would a gear. The edges of the grooves need to be
rounded over to prevent cutting the blets.
>>but what are the formulas to use?
Discussion Thread
wanliker@a...
2000-11-09 21:53:55 UTC
Toothed pully design information needed.
Wally K
2000-11-10 00:44:36 UTC
Re: Toothed pully design information needed.
Alan Marconett KM6VV
2000-11-10 11:16:30 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
Smoke
2000-11-10 11:41:20 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
wanliker@a...
2000-11-10 18:53:55 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
wanliker@a...
2000-11-10 18:54:04 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
Smoke
2000-11-10 21:30:45 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
ptengin@a...
2000-11-10 21:39:03 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
Brian Pitt
2000-11-10 22:22:20 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
ballendo@y...
2000-11-11 04:25:05 UTC
Re: Toothed pully design information needed.
Smoke
2000-11-11 09:12:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toothed pully design information needed.
machines@n...
2000-11-11 09:45:14 UTC
Re: Toothed pully design information needed.
Smoke
2000-11-11 11:00:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toothed pully design information needed.
ptengin@a...
2000-11-11 15:05:09 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
Ian Wright
2000-11-11 15:13:30 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
ptengin@a...
2000-11-11 15:42:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toothed pully design information needed.
ballendo@y...
2000-11-11 15:43:18 UTC
Re: Re: Toothed pully design information needed.
machines@n...
2000-11-11 15:53:55 UTC
Re: Toothed pully design information needed.
wanliker@a...
2000-11-11 16:22:04 UTC
Re: [CAD_CAM_EDM_DRO] Toothed pully design information needed.
Smoke
2000-11-11 20:13:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Toothed pully design information needed.