CAD CAM EDM DRO - Yahoo Group Archive

Re: re: tapers post (for smoke)

on 2000-11-12 19:28:11 UTC
Smoke,

Regarding tapers....you mentioned making some tooling for 5C, etc.
In case you're making a spindle to seat a 5C, be aware that on work
holding collets like 5C's the seat and the collet don't have the
exact same taper. I've forgotten all the details, but when we were
regrinding the 5C taper in one of our Hardinge lathes Hardinge techs
told us to have the spindle angle something like about one degree off
from the collet angle.

Not sure if the above is true for a tool holding collet like an R8.

Doug



--- In CAD_CAM_EDM_DRO@egroups.com, "Smoke" <Smoke@5...> wrote:
> Ah..thanks...I hadn't gone to the web page that shows the 5C
collets. I was
> looking at the spindle nose page.
>
> Smoke
>
> -----Original Message-----
> From: ballendo@y... <ballendo@y...>
> To: CAD_CAM_EDM_DRO@egroups.com <CAD_CAM_EDM_DRO@egroups.com>
> Date: Sunday, November 12, 2000 5:59 PM
> Subject: [CAD_CAM_EDM_DRO] Re: re: tapers post (for smoke)
>
>
> >Smoke,
> >
> >At:
> >
> >http://www.cox-internet.com/drspiff/HSM/Collets/Collets.htm
> >
> >Under R8 OAL is 3.98 . length TO taper is 2.93 . So taper length
is
> >1.03. As mentioned before, diameters (taper) are given.
> >
> >Under 5C Length of taper is called out as 16.3 . Again, dia. are
> >given.
> >
> >
> >Hope this helps
> >
> >Ballendo
> >
> >
> >>Nope...the overall length is show but nothein tha thows length of
> >>taper.
> >>Smoke
> >
> >
> >
> >
> >Welcome to CAD_CAM_EDM_DRO@e...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> >Addresses:
> >Post message: CAD_CAM_EDM_DRO@egroups.com
> >Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> >Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> >List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@a...
> >Moderator: jmelson@a... [Moderator]
> >URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> >FAQ: http://www.ktmarketing.com/faq.html
> >bill,
> >List Manager
> >
> >
> >

Discussion Thread

ballendo@y... 2000-11-12 16:36:11 UTC re: tapers post (for smoke) Smoke 2000-11-12 16:44:13 UTC Re: [CAD_CAM_EDM_DRO] re: tapers post (for smoke) ballendo@y... 2000-11-12 17:00:57 UTC Re: re: tapers post (for smoke) Smoke 2000-11-12 18:00:59 UTC Re: [CAD_CAM_EDM_DRO] Re: re: tapers post (for smoke) dougrasmussen@c... 2000-11-12 19:28:11 UTC Re: re: tapers post (for smoke) Smoke 2000-11-12 20:12:40 UTC Re: [CAD_CAM_EDM_DRO] Re: re: tapers post (for smoke) dougrasmussen@c... 2000-11-12 20:57:31 UTC Re: re: tapers post (for smoke) Smoke 2000-11-12 22:06:53 UTC Re: [CAD_CAM_EDM_DRO] Re: re: tapers post (for smoke)