CAD CAM EDM DRO - Yahoo Group Archive

Re: Quiet list

Posted by Peter Smith
on 1999-08-06 10:59:40 UTC
-----Original Message-----
From: WAnliker@... <WAnliker@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Friday, August 06, 1999 2:54 PM
Subject: [CAD_CAM_EDM_DRO] Quiet list


>From: WAnliker@...
>
>The list has been very quiet lately, is it because:
>1. Everyone is trying to get LINUX running?
>2. Everyone has LINUX running?
>3. Everyone making the DRO Board?
>4. Gave up on LINUX and looking for an alternate? How is Nester doing?
>5. Everyone on the list has joined the ranks of the lurkers?
>6. Everyone is working on the project that is going to be our next
breakthru?
>
>We have 239 members signed up, as of this morning.
>Dying for something to read.
>bill
>List Manager

Bill
I am waiting for Dans 5 amp stepper kit to arrive, with DeskNC, (can't
wait to get the soldering iron onto the gas ring) I will have to start
to take a look at G codes because I have not used these before, all my
programming has been in PR, PA format, (any advice appreciated). I have
been finnishing off a small 6 station tailstock turret for an old IXL lathe
which I use for Making brass terminals, I have this lathe and a Le Blonde
10" Regal which is very nice but can't do some of the things the IXL can do.
The IXL could probaly do with a retro CNC kit fitting, as I do quite a bit
of repitition work with it,
I always thought it was of more use to CNC a mill rather than a lathe

>How is bar feeding catered for on a small CNC lathe? and do you have to
use a servo system for the main drive speeds, and threading feed rate, etc
as I suspect a stepper would not be fast enough as a main drive motor ?
This has always put me off CNCing a lathe, but maybee someone has some
simple answers to the above,

Best Wishes

Peter Smith
>--------------------------- ONElist Sponsor ----------------------------
>
>Congratulations COUNTRYSIDE-ELIST. Our latest ONElist of the week.
>For full story and to submit yours,
><a href=" http://www.onelist.com/info/ootw_20.html ">Click Here</A>
>
>------------------------------------------------------------------------
>Welcome to CAD_CAM_EDM_DRO@...,an unmodulated list for the
discussion of shop built systems in the above catagories.
>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>bill,
>List Manager
>

Discussion Thread

WAnliker@x... 1999-08-06 06:54:27 UTC Quiet list Peter Smith 1999-08-06 10:59:40 UTC Re: Quiet list John Ross 1999-08-06 11:32:22 UTC RE: Quiet list Steve Gunsel 1999-08-06 12:29:05 UTC Re: Quiet list paul@x... 1999-08-06 12:34:05 UTC Re: Quiet list Bob Bachman 1999-08-06 17:51:06 UTC Re: Quiet list PTENGIN@x... 1999-08-06 15:04:25 UTC Re: Quiet list Bob Bachman 1999-08-06 18:56:14 UTC Re: Quiet list Jon Elson 1999-08-06 22:12:10 UTC Re: Quiet list Tim Goldstein 1999-08-06 22:18:48 UTC RE: Quiet list Bob Bachman 1999-08-07 09:20:43 UTC RE: Quiet list Dan Mauch 1999-08-07 07:07:17 UTC Re: Quiet list Steve Gunsel 1999-08-07 12:10:51 UTC Re: Quiet list Ian W. Wright 1999-08-06 15:04:55 UTC Re: Quiet list Bob Bachman 1999-08-07 16:12:13 UTC Re: Quiet list Ian W. Wright 1999-08-07 12:25:33 UTC Re: Quiet list Dan Mauch 1999-08-07 17:36:49 UTC Re: Quiet list DHolness@x... 1999-08-09 09:23:37 UTC Re: Quiet list Dan Mauch 1999-08-13 13:21:40 UTC Re: Quiet list DHolness@x... 1999-08-13 14:42:50 UTC Re: Quiet list Dan Mauch 1999-08-13 15:58:34 UTC Re: Quiet list