Re: [CAD_CAM_EDM_DRO] mill drill gibs was Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
Posted by
Peter Smith
on 2001-03-17 07:27:01 UTC
Just turn an adjusting screw up with a head that fits the gib exactly, I did
this :- no more problem, the gib remains in location in both directions,
screwcut the thread to be a slightly tight fit in the body.
Peter Smith
this :- no more problem, the gib remains in location in both directions,
screwcut the thread to be a slightly tight fit in the body.
Peter Smith
----- Original Message -----
From: <ballendo@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: 17 March 2001 00:10
Subject: [CAD_CAM_EDM_DRO] mill drill gibs was Dan Ms' Mill drill Re:
GeckoDrives.. Servo motor
> Re: mill/drill gibs
>
> Drill and tap the gib for a plate which "closes the gap". Use
> loctite, or similar threadlocker(light duty type) on the adjustment
> screw. Cheap, fast, simple, works.
>
> Ballendo
>
>
> >Did you do anything with your gibb adjustments? On mine the slot in
> >the gibb that the adjustment screw head rides in is wider than the
> >screw head and the gibb moves back and forth a bit everytime the
> axis changes direction. Also there is no way to lock the adjustment
> down, so It wanders
> > > >around on it's own.
> >
> > I ended up brazing a bracket on the end of the gib so I could do a
> decent adjustment and have it stay put.
> >
> > Dave
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
Dan Mauch
2001-03-15 06:58:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: GeckoDrives.. Servo motor
cadman@p...
2001-03-15 08:14:59 UTC
GeckoDrives help... Thanks to all
ballendo@y...
2001-03-16 05:10:52 UTC
Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
Dan Mauch
2001-03-16 07:42:52 UTC
Re: [CAD_CAM_EDM_DRO] Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
Joel Jacobs
2001-03-16 08:26:53 UTC
Re: [CAD_CAM_EDM_DRO] Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
Dan Mauch
2001-03-16 09:33:18 UTC
Re: [CAD_CAM_EDM_DRO] Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
dave engvall
2001-03-16 10:29:52 UTC
Re: [CAD_CAM_EDM_DRO] Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
ballendo@y...
2001-03-16 15:50:02 UTC
Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
ballendo@y...
2001-03-16 16:10:30 UTC
mill drill gibs was Dan Ms' Mill drill Re: GeckoDrives.. Servo motor
Peter Smith
2001-03-17 07:27:01 UTC
Re: [CAD_CAM_EDM_DRO] mill drill gibs was Dan Ms' Mill drill Re: GeckoDrives.. Servo motor