CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Re: +/- 10V Gecko

Posted by dave engvall
on 2001-03-22 22:40:25 UTC
Jon Elson wrote:

> Ray wrote:
>
>
>
> > Think of it, with four Gecko 330's you can have 6.4 kw surround sound.
> > Even the neighbors dog will leave the patch!

I have this voice coil off a 100 Mb 11 platter DEC disk drive. Should make a good sub-woofer driving
a big styrofoam panel. :-)


>
>
>
>
> Jon
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

mariss92705@y... 2001-03-21 16:06:04 UTC +/- 10V Gecko Matt Shaver 2001-03-21 17:28:51 UTC Re: [CAD_CAM_EDM_DRO] +/- 10V Gecko mariss92705@y... 2001-03-21 18:01:20 UTC Re: +/- 10V Gecko Jon Elson 2001-03-21 21:03:54 UTC Re: [CAD_CAM_EDM_DRO] +/- 10V Gecko Brian Pitt 2001-03-21 22:07:23 UTC Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko mariss92705@y... 2001-03-21 22:14:41 UTC Re: +/- 10V Gecko Tom Eldredge 2001-03-22 08:21:30 UTC Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko mariss92705@y... 2001-03-22 09:18:47 UTC Re: +/- 10V Gecko Jon Elson 2001-03-22 11:39:58 UTC Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko Jon Elson 2001-03-22 12:15:25 UTC Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko mariss92705@y... 2001-03-22 13:06:44 UTC Re: +/- 10V Gecko Jon Elson 2001-03-22 14:52:10 UTC Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko Ray 2001-03-22 19:51:27 UTC Re: Re: +/- 10V Gecko Jon Elson 2001-03-22 21:51:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: +/- 10V Gecko dave engvall 2001-03-22 22:40:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: +/- 10V Gecko