Re: +/- 10V Gecko
Posted by
mariss92705@y...
on 2001-03-21 18:01:20 UTC
Matt,
1) Included, but was not mentioned
2) Included, but was not mentioned
3) Perhaps combined with (2)? Pull both down and motor stops.
4) Makes sense!
Mariss
1) Included, but was not mentioned
2) Included, but was not mentioned
3) Perhaps combined with (2)? Pull both down and motor stops.
4) Makes sense!
Mariss
--- In CAD_CAM_EDM_DRO@y..., Matt Shaver <mshaver@e...> wrote:
> mariss92705@y... wrote:
>
> I could be really happy with the amp you've described, but here are
a
> few ideas for additional features in descending order of importance
(#1
> is critical, #2 is desirable, and the rest are gingerbread):
>
> 1. Fault Output - lets the control know the amp has been shut down
by
> its internal protection circuitry.
>
> 2. Enable Input - lets the control enable the amp or allow the
motor to
> freewheel.
>
> 3. + & - inhibit inputs - for limit switches (I don't need these,
but
> other amps I've used have them).
>
> 4. Voltage output proportional to motor current - Servo Dynamics
has
> this on their amps, and Jon Elson's amps had an LED bar graph
display on
> the card edge.
>
> I've got to save up some money to buy something from you so that I
can
> get grandfathered in as a customer before the opportunity passes.
The
> combination of Gecko drives, the parallel port motion controller,
and an
> easy to use version of the EMC would be a great product if it were
> packaged up in a ready to use kit.
>
> Matt
Discussion Thread
mariss92705@y...
2001-03-21 16:06:04 UTC
+/- 10V Gecko
Matt Shaver
2001-03-21 17:28:51 UTC
Re: [CAD_CAM_EDM_DRO] +/- 10V Gecko
mariss92705@y...
2001-03-21 18:01:20 UTC
Re: +/- 10V Gecko
Jon Elson
2001-03-21 21:03:54 UTC
Re: [CAD_CAM_EDM_DRO] +/- 10V Gecko
Brian Pitt
2001-03-21 22:07:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko
mariss92705@y...
2001-03-21 22:14:41 UTC
Re: +/- 10V Gecko
Tom Eldredge
2001-03-22 08:21:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko
mariss92705@y...
2001-03-22 09:18:47 UTC
Re: +/- 10V Gecko
Jon Elson
2001-03-22 11:39:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko
Jon Elson
2001-03-22 12:15:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko
mariss92705@y...
2001-03-22 13:06:44 UTC
Re: +/- 10V Gecko
Jon Elson
2001-03-22 14:52:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: +/- 10V Gecko
Ray
2001-03-22 19:51:27 UTC
Re: Re: +/- 10V Gecko
Jon Elson
2001-03-22 21:51:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: +/- 10V Gecko
dave engvall
2001-03-22 22:40:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: +/- 10V Gecko