Re: [CAD_CAM_EDM_DRO] deep pocket milling
Posted by
Rich D.
on 2001-03-24 13:01:54 UTC
Vic,
My procedure is to use a very slow rpm in the corners (and feed rate).
Also, another trick, before finishing the straight walls, retract the cutter,
position at the corner and plunge. Do this at each corner. Now finish the walls.
Done carefully it works.
Rich D.
"Victor Cantu Jr." wrote:
My procedure is to use a very slow rpm in the corners (and feed rate).
Also, another trick, before finishing the straight walls, retract the cutter,
position at the corner and plunge. Do this at each corner. Now finish the walls.
Done carefully it works.
Rich D.
"Victor Cantu Jr." wrote:
>
> I have recently had to make a part that required a deep pocket in the center. The pocket was 2x3x3deep. I got the part done but, I wasn't satisfied with the chatter I got in the corners. the mat. was alluminum 60-61 . Does any one have any suggestions for me they would be greatly appreciated. thanks
>
> [Non-text portions of this message have been removed]
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Victor Cantu Jr.
2001-03-24 10:24:02 UTC
deep pocket milling
Jon Anderson
2001-03-24 11:12:31 UTC
Re: [CAD_CAM_EDM_DRO] deep pocket milling
Rich D.
2001-03-24 13:01:54 UTC
Re: [CAD_CAM_EDM_DRO] deep pocket milling
Jon Elson
2001-03-24 20:28:38 UTC
Re: [CAD_CAM_EDM_DRO] deep pocket milling
Victor Cantu Jr.
2001-03-29 01:40:54 UTC
deep pocket milling
Marcus & Eva
2001-03-29 08:33:18 UTC
Re: [CAD_CAM_EDM_DRO] deep pocket milling
John Stevenson
2001-03-29 09:21:31 UTC
Re: deep pocket milling
Tony Jeffree
2001-03-29 14:15:52 UTC
Re: [CAD_CAM_EDM_DRO] deep pocket milling
John Stevenson
2001-03-29 14:31:12 UTC
Re: deep pocket milling
Spehro Pefhany
2001-03-29 14:45:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: deep pocket milling
Marcus
2001-03-29 15:59:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: deep pocket milling
Tony Jeffree
2001-03-29 22:26:14 UTC
Re: [CAD_CAM_EDM_DRO] deep pocket milling
Bill Darby
2001-03-30 04:22:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: deep pocket milling
marble here
2001-03-30 05:54:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: deep pocket milling
Marcus & Eva
2001-03-30 07:42:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: deep pocket milling
Bill Darby
2001-04-01 11:12:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: deep pocket milling