CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen

Posted by Joel Jacobs
on 2001-05-04 07:53:10 UTC
Old 70's era big stereo receivers have some pretty healthy transformers in
them that usually produce 60-80 volts after the rectifires/filters. You
might check with a local electronics repair shop, they might have dead ones
lying around you could get real cheap.
Joel

----- Original Message -----
From: "Matt Shaver" <mshaver@...>

> I spoke with Marty on the phone this evening and I think he could also
> use some recommendations on how to build an inexpensive 80V supply if he
> goes with Gecko drives.
>
> Matt

Discussion Thread

cnc002@a... 2001-05-03 07:50:42 UTC Re: [CAD_CAM_EDM_DRO] TurboCNC dkowalcz@i... 2001-05-03 17:47:24 UTC Re: TurboCNC Marty Escarcega 2001-05-03 19:38:09 UTC Thoughts on PC Based Control Retrofit....pictures of the specimen Marty Escarcega 2001-05-03 19:59:12 UTC Re: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Matt Shaver 2001-05-03 21:18:18 UTC Re: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Tim Goldstein 2001-05-03 21:40:02 UTC RE: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Matt Shaver 2001-05-03 22:46:52 UTC Re: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Tim Goldstein 2001-05-03 23:08:42 UTC RE: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Marty Escarcega 2001-05-04 06:19:24 UTC RE: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Joel Jacobs 2001-05-04 07:53:10 UTC Re: [CAD_CAM_EDM_DRO] Thoughts on PC Based Control Retrofit....pictures of the specimen Carol & Jerry Jankura 2001-05-04 15:15:10 UTC RE: [CAD_CAM_EDM_DRO] Re: TurboCNC cnc002@a... 2001-05-05 07:00:15 UTC Re: [CAD_CAM_EDM_DRO] Re: TurboCNC Carol & Jerry Jankura 2001-05-05 09:21:04 UTC RE: [CAD_CAM_EDM_DRO] Re: TurboCNC dkowalcz@i... 2001-05-05 19:42:45 UTC Re: TurboCNC cnc002@a... 2001-05-06 06:54:03 UTC Re: [CAD_CAM_EDM_DRO] Re: TurboCNC cnc002@a... 2001-05-06 07:00:32 UTC Re: [CAD_CAM_EDM_DRO] Re: TurboCNC Carol & Jerry Jankura 2001-05-06 17:56:21 UTC RE: [CAD_CAM_EDM_DRO] Re: TurboCNC dkowalcz@i... 2001-05-07 06:12:49 UTC Re: TurboCNC Doug Fortune 2001-05-07 07:48:52 UTC TurboCNC cnc002@a... 2001-05-07 07:50:32 UTC Re: [CAD_CAM_EDM_DRO] Re: TurboCNC mgrady 2001-05-08 03:55:51 UTC Re: [CAD_CAM_EDM_DRO] Re: TurboCNC ballendo@y... 2001-05-08 04:14:20 UTC Re: TurboCNC Tim Goldstein 2002-03-07 00:10:37 UTC TurboCNC wanliker@a... 2006-05-22 23:39:45 UTC TurboCNC Dave Kowalczyk 2006-05-23 07:59:00 UTC Re: TurboCNC Tom Hubin 2006-05-23 09:01:55 UTC Re: [CAD_CAM_EDM_DRO] TurboCNC wanliker@a... 2006-05-23 10:59:39 UTC Re: [CAD_CAM_EDM_DRO] Re: TurboCNC wanliker@a... 2006-05-23 11:04:27 UTC TurboCNC