Re: [CAD_CAM_EDM_DRO] Re: RF-45
Posted by
Alan Marconett KM6VV
on 2001-05-15 11:11:29 UTC
Hi Peter,
Thanks! I looked it up in MSC, not in stock. And I've been told it's
about $300+ shipping. ENCO's free shipping (well, almost) starts to
look better. Would RongFu be a little better then ENCO? Taiwan vs
China?
Alan KM6VV
So many mills, so little time (money).
ptengin@... wrote:
Thanks! I looked it up in MSC, not in stock. And I've been told it's
about $300+ shipping. ENCO's free shipping (well, almost) starts to
look better. Would RongFu be a little better then ENCO? Taiwan vs
China?
Alan KM6VV
So many mills, so little time (money).
ptengin@... wrote:
>
> In a message dated 5/14/01 3:39:05 PM Hawaiian Standard Time,
> ronginger@... writes:
>
> << I believe the RongFu 45 is sold by Penn Tool. I have seen other catalogs
> that list some RongFu, but not the 45.
>
> ron ginger >>
> Ron,
>
> I believe MSC has them, there is a look alike at Grizzly too. BTW the
> RF-45 weighs about 700 lbs.
>
> Peter
> THRD, Inc.
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
ptengin@a...
2001-05-15 03:14:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 11:11:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Joe Vicars
2001-05-15 11:16:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 12:09:25 UTC
Re: RF-45
Drew Rogge
2001-05-15 12:18:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Drew Rogge
2001-05-15 12:21:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Joe Vicars
2001-05-15 12:21:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
rfs@c...
2001-05-15 16:20:10 UTC
Re: RF-45
Alan Marconett KM6VV
2001-05-15 16:33:10 UTC
Re: RF-45
Drew Rogge
2001-05-15 16:53:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 17:20:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 17:43:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 18:12:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Doug Harrison
2001-05-15 18:47:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 19:59:11 UTC
Re: RF-45
ballendo@y...
2001-05-15 20:15:22 UTC
Reality check? was Re: RF-45
dave engvall
2001-05-15 20:19:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
ptengin@a...
2001-05-17 01:35:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45