Re: [CAD_CAM_EDM_DRO] Re: RF-45
Posted by
ptengin@a...
on 2001-05-15 03:14:22 UTC
In a message dated 5/14/01 3:39:05 PM Hawaiian Standard Time,
ronginger@... writes:
<< I believe the RongFu 45 is sold by Penn Tool. I have seen other catalogs
that list some RongFu, but not the 45.
ron ginger >>
Ron,
I believe MSC has them, there is a look alike at Grizzly too. BTW the
RF-45 weighs about 700 lbs.
Peter
THRD, Inc.
ronginger@... writes:
<< I believe the RongFu 45 is sold by Penn Tool. I have seen other catalogs
that list some RongFu, but not the 45.
ron ginger >>
Ron,
I believe MSC has them, there is a look alike at Grizzly too. BTW the
RF-45 weighs about 700 lbs.
Peter
THRD, Inc.
Discussion Thread
ptengin@a...
2001-05-15 03:14:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 11:11:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Joe Vicars
2001-05-15 11:16:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 12:09:25 UTC
Re: RF-45
Drew Rogge
2001-05-15 12:18:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Drew Rogge
2001-05-15 12:21:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Joe Vicars
2001-05-15 12:21:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
rfs@c...
2001-05-15 16:20:10 UTC
Re: RF-45
Alan Marconett KM6VV
2001-05-15 16:33:10 UTC
Re: RF-45
Drew Rogge
2001-05-15 16:53:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 17:20:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 17:43:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 18:12:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Doug Harrison
2001-05-15 18:47:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 19:59:11 UTC
Re: RF-45
ballendo@y...
2001-05-15 20:15:22 UTC
Reality check? was Re: RF-45
dave engvall
2001-05-15 20:19:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
ptengin@a...
2001-05-17 01:35:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45