Re: RF-45
Posted by
rfs@c...
on 2001-05-15 16:20:10 UTC
Hello Joe...
Just jumping into this thread. Looked at the RF45 pix in the files
section...nice appearing machine. Are you suggesting changing the
mill x/y over to CNC with existing screws or replacing with ball
screws?
Thanx. Rick (Michigan)
Just jumping into this thread. Looked at the RF45 pix in the files
section...nice appearing machine. Are you suggesting changing the
mill x/y over to CNC with existing screws or replacing with ball
screws?
Thanx. Rick (Michigan)
--- In CAD_CAM_EDM_DRO@y..., Joe Vicars <jvicars@c...> wrote:
> Alan,
> Reno is the closest. So if you were in Sacramento or San Fran it
would be a pretty short trip.
> San Diego and L.A. is a pretty far drive though.
> They don't seem to have anything in the Northwest.
>
> Alan Marconett KM6VV wrote:
>
> > Hi Joe,
> >
> > No MSC locations in CA, so I guess that's out.
> >
> > Alan KM6VV
> >
> > Joe Vicars wrote:
> > >
> > > MSC has lots of distribution centers. I wonder if you could
pick it up yourself at one of their warehouses without having to pay
the
> > > freight?
> > > Anybody know?
> > >
> > > Alan Marconett KM6VV wrote:
> > >
> > > > Hi Peter,
> > > >
> > > > Thanks! I looked it up in MSC, not in stock. And I've been
told it's
> > > > about $300+ shipping. ENCO's free shipping (well, almost)
starts to
> > > > look better. Would RongFu be a little better then ENCO?
Taiwan vs
> > > > China?
> > > >
> > > > Alan KM6VV
> > > > So many mills, so little time (money).
> > > >
> > > > ptengin@a... wrote:
> > > > >
> > > > > In a message dated 5/14/01 3:39:05 PM Hawaiian Standard
Time,
> > > > > ronginger@r... writes:
> > > > >
> > > > > << I believe the RongFu 45 is sold by Penn Tool. I have
seen other catalogs
> > > > > that list some RongFu, but not the 45.
> > > > >
> > > > > ron ginger >>
> > > > > Ron,
> > > > >
> > > > > I believe MSC has them, there is a look alike at Grizzly
too. BTW the
> > > > > RF-45 weighs about 700 lbs.
> > > > >
> > > > > Peter
> > > > > THRD, Inc.
> >
> > Welcome to CAD_CAM_EDM_DRO@e...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@y...
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> > FAQ: http://www.ktmarketing.com/faq.html
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
Discussion Thread
ptengin@a...
2001-05-15 03:14:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 11:11:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Joe Vicars
2001-05-15 11:16:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 12:09:25 UTC
Re: RF-45
Drew Rogge
2001-05-15 12:18:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Drew Rogge
2001-05-15 12:21:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Joe Vicars
2001-05-15 12:21:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
rfs@c...
2001-05-15 16:20:10 UTC
Re: RF-45
Alan Marconett KM6VV
2001-05-15 16:33:10 UTC
Re: RF-45
Drew Rogge
2001-05-15 16:53:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 17:20:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 17:43:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 18:12:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Doug Harrison
2001-05-15 18:47:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
Alan Marconett KM6VV
2001-05-15 19:59:11 UTC
Re: RF-45
ballendo@y...
2001-05-15 20:15:22 UTC
Reality check? was Re: RF-45
dave engvall
2001-05-15 20:19:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45
ptengin@a...
2001-05-17 01:35:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45