CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: Sanyo Motor

on 2001-05-25 16:57:25 UTC
It's a size 23 mount, approximately 2 1/2 inches deep.

-- Carol & Jerry Jankura
Strongsville, Ohio
So many toys, so little time



-----Original Message-----
From: admin@... [mailto:admin@...]
Sent: Friday, May 25, 2001 7:44 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Sanyo Motor


--- In CAD_CAM_EDM_DRO@y..., "Carol & Jerry Jankura"
<jerry.jankura@s...> wrote:
> Folks:
>
> I've come across some Sanyo stepper motors and wonder if anyone has
torque> specifications for them, or knows where I would look. I
already checked the> Sanyo web site, and their current offerings do
not match this number. I> believe that the motor was originally OEM'd
to IBM. The Sanyo part is:> 103G770-2516
>
> The motor is rated 4.1volts @1.1 amp.
>
> Also, would these motors be suitable for driving a Sherline 4400
lathe and> Sherline 2000 mill?
Carol & Jerry Jankura


Carol and Jerry,

It was good to include the electrical specs, but
we need the physical size of the motor as well.

That, more than anything else; is your best guide
to estimating torque. The same size motor can
be made with an infinite variety of windings;
all of which produce about the same holding-torque;
but differ in driver-requirements, speed capability,
etc..

I doubt that part number means anything. It's almost
certainly an OEM part number; for IBM or whoever.

If it's a typical "IBM printer stepper", it's a
single-stack size-34, with a funky shaft-size <g>,
and a 2-deg step angle. I.e., 180 steps/rev instead
of the more common 200/rev.

And if that's what it is, then it's about 125 oz-in,
give or take 20%.

Hope this helps a bit,

Richard


Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.

Addresses:
Post message: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager

FAQ: http://www.ktmarketing.com/faq.html

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

Carol & Jerry Jankura 2001-05-25 15:53:47 UTC Sanyo Motor RC 2001-05-25 16:16:52 UTC Re: [CAD_CAM_EDM_DRO] Sanyo Motor admin@a... 2001-05-25 16:47:11 UTC Re: Sanyo Motor admin@a... 2001-05-25 16:55:05 UTC Re: Sanyo Motor Carol & Jerry Jankura 2001-05-25 16:57:25 UTC RE: [CAD_CAM_EDM_DRO] Re: Sanyo Motor Carol & Jerry Jankura 2001-05-25 17:04:27 UTC RE: [CAD_CAM_EDM_DRO] Re: Sanyo Motor Chris Stratton 2001-05-25 17:21:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Sanyo Motor admin@a... 2001-05-25 17:35:48 UTC Re: Sanyo Motor alenz@c... 2001-05-25 22:41:20 UTC Re: Sanyo Motor RC 2001-05-26 04:05:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Sanyo Motor